Wayne-Dalton 8000 Installation Instructions And Owner's Manual

Also see for 8000 Series: Installation instructions and owner's manual Installation instructions and owner's manual Installation instructions and owner's manua Installation instructions and owner's manual Quick start guide

Contents

Wayne-Dalton 8000 Installation Instructions And Owner's Manual Manual pdf 3 page image

Graduated hinges(as required)Track rollers(as required)Top fixture slides(as required)Top fixture bases(as required)Top fixtureassemblies (as required) Top fixtures (as required)Bottom corner brackets RH/LH (as required)Center bracket (as required) Center bracketbushing (as required)Counterbalance Lift Cables Cable drums RH/LH Torsion springs RH/LHCenter bracketbearing(as required)Pull down rope(if included)Cotter pin (as required) 5/16” x 1-1/4”Clevis pin (as required)End bearing brackets RH/LH (as required)(2) 1/4” - 20 Hexnuts (lift handles) 3/8”- 16 Hex nuts(as required)5/16”-18 Hex nuts(as required) 1/4”- 20 Flangedhex nuts (as required)(2) Lift handles &Spacers (1) Step plate(as required) Washers(as required)(2) Step plates(as required) (1) Step plates(as required)5/16”-18 x 3/4”Carriage bolts (as required) 1/4”-20 x 7/8” Selfdrilling screws (as required)1/4”-20 x 11/16” Selfdrilling screws (as required)1/4”-20 x 9/16”Track bolts (as required)3/8”-16 x 1-1/2” Hex bolts (as required)(2) #8 x 1-5/8”Self tapping screws (step plate)3/8”-16 x 3/4”Truss head bolts1/4”-14 x 5/8” Self tappingscrews (as required)1/4”-20 x 11/16”Self drilling screws(RED HEAD) (as required)5/16” x 1-5/8” Hex headlag screws (as required)5/16” x 1-5/8” Hex head lag screws(RED HEAD) (as required)(2) 1/4”-20 x 2-1/2” Carriage bolts (lift handles)5/16” x 2-1/2” Hex head lag screws(RED HEAD) (as required)Door Section IdentificationDoor Section identificationDoorHeightBottom Lock Interme-diate IInterme-diate IIInterme-diate IIIInterme-diate IVTop6’0” 18” 18” 18” - 18”6’3” 21” 18” 18” - 18”6’6” 21” 18” 18” - 21”6’9” 21” 21” 21” - 18”7’0” 21” 21” 21” - 21”7’6” 18” 18” 18” 18” - 18”7’9” 21” 18” 18” 18” - 18”8’0” 21” 18” 18” 18” - 21”8’3” 21” 21” 18” 18” - 21”8’6” 21” 21” 21” 21” - 18”8’9” 21” 21” 21” 21” - 21”9’0” 18” 18” 18” 18” 18” - 18”When installing your door you must use sections of the appropriate height in the right stack-ing order. What section heights you need to use in what order depends on the height of yourdoor.Unless your door is five sections in height, you will not receive an Intermediate II section.The BOTTOM SECTION can be identified by the factory attached bottom astragal, the factoryattached bottom corner brackets, and by the bottom corner bracket warning labels on eachend stile.The INTERMEDIATE I SECTION may have a warning label attached to either right or lefthand end stile of the section. This section is always the 3rd section from the bottom of thedoor.18”or21”Section sideview illustrationBottom sectionBottom weather sealBottom corner bracket warning labelsIntermediate I sectionWarning labelRemoving an Existing Door3