Xerox DocuPrint 100 Reference Manual

Also see for Nuvera 100: System guide Getting started Install guide Software guide Planning guide

Contents

Xerox DocuPrint 100 Reference Manual Manual pdf 1 page image

Duty cycleTargeted impressions per month on the XeroxDocuPrint 100/115/135/155/180 EPS:Note: Usage outside these ranges may vary theservice frequency.PerformanceReliability performance of the Xerox DocuPrint 100/115/135/155/180 EPS for the targeted impressions permonth:Note: Variables other than monthly print volume affectthe average number of service calls. Please contactyour local Xerox representative for more information.ResolutionDP 155 and 180: 600 by 2400 dots per inch (dpi)DP 100, 115, and 135: 600 by 600 dots per inch (dpi)SpeedThe speed at which data can be printed on the XeroxDocuPrint 100/115/135/155/180 EPS:Note: Throughput rates can vary depending upon jobcomplexity and system configuration.* Requires optional 7 by 10 inch enablement kit.Paper handling• Paper weights: 16 lbs. / 65 gsm bond to 110 lbs. /200 gsm index cut-sheet weights• Paper sizes:– 8 x 10 in. / 203 x 254 mm to14.33 x 17 in. / 364 by 432 mm, including A4 and A3– 7 x 10 in. / 178 x 254 mm with optional 7 x 10 in.enablement kitInput• Main tray (Tray 1): 1100 sheet capacity of 20 lbs. /80 gsm bond paper• Auxiliary tray (Tray 2): 600 sheet capacity of 20lbs. / 80 gsm bond paperThe Xerox DocuPrint 100/115/135/155/180 EPS mayhave up to six input trays: two processor trays and two,three, or four high-capacity feeder trays.Output• Output bin: Each output bin has a capacity of 2500sheets of 20 lbs. / 80 gsm bond with offsetcapability.Two output bins are standard, with up to twoadditional bins available as options.• Sample tray: 100 sheets of 20 lbs. / 80 gsm bondRefer to Helpful Facts About Paper to help in selectionof preprinted forms, perforated stock and labels.Controller components• Processor (system unit):– One or two UltraSPARC central processing unit(CPU) modules– 1 or 2 GB of memory (one or two 1-GB Dual In-lineMemory Modules, or DIMMs)– 36 or 73 GB hard disk drive– High-density, read-only DVD-ROM drive– Diskette drive: uses 3.5 inch, 1.44 MB, double-sided,high-density diskettes– Ethernet– 1 or 2 Printer Controller Interface (PCI) boards– PGx64 or XVR-100 video graphics board• Universal Serial Bus (USB) keyboard and mouse• 17-inch flat panel monitorNote: This configuration may change due to the Xeroxpolicy of staying up to date with current technology.Supported client workstationsXerox DP 100/115/135/155/180 EPS supports thefollowing types of networked client workstations andoperating systems:• Sun Workstation running Solaris 2.3 or higher• PC running MS-DOS 5.0 or higher, using Ethernetwith TCP/IP or Novell NetWare, and Windows 95/98, NT, Millennium, 2000, or XP• PC running MS-DOS 5.0 or higher, with one or moreof the following TCP/IP packages:– PC/TCP Network Software by FTP Software, Inc.– Pathway Access by Wollongong Group, Inc.– PC-NFS by Sun Select• Apple Macintosh, System 7 or higher, usingAppleTalk through EtherTalk• Any system that supports RFC-1179 lpr/lpdPDL compatibilityThe system interprets the following data formats:• PostScript levels 2 and 3• PCL5e and PCL6• LCDS• ASCII• PDF• TIFF• VIPP• IPDS (currently not available)Interface requirementsOne or more of the following network communicationssystems may be used to transport documents from aclient or host to the printing system.• Ethernet LAN running TCP/IP, AppleTalk, or NovellNetWare network protocol software• Online – Bus and tag supporting IBM 3211/4245interface*• Token ring LAN running TCP/IP, Novell 3.x, orAppleTalk network protocol software** Requires additional equipment.Installation considerations• Data cable: The controller can be separated up tothe length of the data interface cables that connectsthem.– 20 foot / 6.1 meters, or– Optional 50 foot / 15.2 meters• Power cable lengths are as follows:• Cable length loss must be factored in if equipment isinstalled in a raised-floor environment. Part of thecable length is routed inside the equipment toconnect with interior power receptacles.• All power cords attach to the back of the printer.Listed below are the distances of the printer powercord attachments from the left end of the printer asyou face it:– Cord #1: 36 inches / 914 mm– Cord #2: 23 inches / 584 mm (DP 155 & 180)Special considerations• Transference of the black toner to poly-vinylsurfaces is a common occurrence.• When printing edge to edge, there is a 3 to 4.8 mmborder around the sheet where degraded imagequality may occur.• Edge marking should be no closer than 4.8 mm fromthe edge of the sheet.• Xerox carbonless paper is approved for XeroxDocuPrint 100/115/135/155/180 EPS. Refer to theXerox Supplies Catalog for the reorder numbers.• Appearance of very small spots is a commonoccurrence on all xerographic printers. Consult yourXerox service representative for details onacceptable spot occurrence specifications.Printing system Minimum MaximumDP100 800 thousand 3 millionDP115 1 million 3.5 millionDP135 1.2 million 4 millionDP155 1.4 million 4.5 millionDP180 1.8 million 6 millionAveragemonthlyprintvolumeAverageservicecalls permonthDP100Averageservicecalls permonthDP115Averageservicecalls permonthDP135Averageservicecalls permonthDP155Averageservicecalls permonthDP1801million2.7 2.6 2.5 2.6 2.42million5.4 5.2 5.0 5.2 4.83million8.1 7.8 7.5 7.8 7.24million-- -- 10.0 10.4 9.65million-- -- -- -- 126million -- -- -- -- 14.4Printing systemPages per minute(standard)Pages per minute(using 7 x 10 in. /178 x 254 mmpaper) *DP100 100 100DP115 115 115DP135 135 154DP155 155 155DP180 180 206Controller: 8 feet / 2.4 mPrinter: 15 feet / 4.6 m

/ 2

Related manuals for Xerox Nuvera 100