Environmental requirementsSuppliesNotes:• Expected dry ink yield is based on a 7 percent areacoverage, 8.5 by 11 inch or A4 paper, and variesdepending on area coverage of the application, aswell as the darkness settings of the printer.• Contact your local Xerox representative for suppliesordering information.Recommended Minimum MaximumOperatingtemperature 72 o +/- 4 o F22 o +/- 2 o C50 o F10 o C85 o F29 o CHumidity 45% +/- 10% RH 30% RH 65% RHNormal MaximumAltitude Up to 6,000 feet /1,830 m abovesea level9,000 feet /2,743 m abovesea levelHeat dissipation Standby RunningPrinter 4,454 BTU/hr.(Fuser on)2,700 BTU/hr.(Energy saver)155/180: 32,770BTU/hr100/115/135:28,140 BTU/hr.Processor andmonitor (SunBladeTM )SB 1000/2000: 1,100 BTU/hr.SB 2500: 1,570 BTU/hr.Reorder number Expected yield(Prints/carton)Dry ink US: 6R206Europe: 6R90100 180,000Dry ink wastebottle US: 93K460Europe: 93K450 N/ADeveloper US: 5R161Europe: 5R900951,000,000Fuser agent US: 8R2955Europe: 8R90163 250,000(1 bottle)MICR dry ink US: 6R819 180,000MICRdeveloper US: 5R573 600,000• In the U.S., call 1.800.822.2200 to order Xeroxsupplies, including paper and other stocks.Space requirementsNotes:• All the dimensions are taken from the system frameto the nearest wall or obstruction, shown in inchesand centimeters, and are absolute minimums.• There should be a minimum of 78 inches / 198 cmclearance from the floor to the nearest overheadobstruction, throughout the entire area.Depth Width HeightControllerThe following data is accurate for the Sun BladeTM1000/2000 and 2500 workstations, and is presentedas an example of typical space requirements forworkstations.Stand 35.5 in.90.2 cm30 in.76.2 cm38.25 in.97.2 cmProcessor: SunBladeTM 1000/200019.3 in.49 cm8.2 in.21 cm17.75 in.45.1 cmProcessor: SunBladeTM 2500 25 in.63.5 cm10 in.25.4 cm19 in.46.3 cmMonitor 10 in.25.4 cm17 in.43.2 cm18.5 in.47 cmPrinterSpace requirements (physical hardware and requiredservice area) for each of the printer configurations:With inverter feeder/stacker and 1 feeder/stacker114 in.290 cm223 in.567 cmWith inverter feeder/stacker and 2 feeder/stackers114 in.290 cm257 in.652.8 cmWith inverter feeder/stacker and 3 feeder/stackers114 in.290 cm288 in.731 cmWith inverter feeder/stacker, feeder/stacker, and bypasstransport module114 in.290 cm242 in.615 cmWith inverter feeder/stacker and 2 feeder/stackers, and bypasstransport114 in.290 cm276 in.701 cm• The printing system must be installed in a fixedlocation with minimum clearance space of 36 inches/ 91.4 cm around all sides of each piece ofequipment for access by service personnel.• 50 inches / 127 cm clearance space is required infront of the printer.• The controller must be positioned within the line ofsight of the printer for safety purposes while theequipment is being serviced.• Customer must use the Xerox-supplied stand for allcontroller components. Space requirements for thecontroller stand are 36 by 36 inches / 91 by 91 cm.• For proper operation, the printer must be perfectlylevel. On floors less than two degrees out of level, aleveling kit must be used to level the equipment.The printer will not function properly on floors morethan two degrees out of level.For additional space/configuration options, refer to theXerox DocuPrint 100/115/135/155/180 EPSInstallation Planning Guide.Electrical requirementsNotes:• Dedicated service is required for each component.Each power cord must have a separate circuit.• Power requirements of the bypass transport aresatisfied by the printer module.Controller(47-63 Hz)Printer(60 Hz)Cord #1155/180printer(60 Hz)Cord #2Printer(50 Hz)Voltage 100-240VAC(1 phase)120/208VAC; or120/240VAC(2 phase)120/208VAC; or120/240VAC(2 phase)380, 400,415 VAC(3 phase)Recep-tacleNEMA partnumber5-15R 14-50R 14-30R --Powerconsump-tion (KVA)Operatingmode0.4 7.3 +.75 permiddlemodulestacker7.3+.75 permiddlemodulestackerConsultyour localservicerepresentative2004 by Xerox Corporation. All rights reserved.Xerox DocuPrint100/115/135/155/180 EPSCustomer InformationQuick Reference CardVersion 4.1September 2004701P42238