Phaser® 6250 Color Laser PrinterCopyright © 2003 Xerox Corporation. All Rights Reserved.4-3Paper JamsThis topic includes:■ "Misfeed at Tray 1 (MPT)" on page 4-3■ "Misfeed at Tray 2, 3, or 4" on page 4-5■ "Jam at the Fuser" on page 4-8■ "Jam at the Duplex Unit" on page 4-10For safety information, go to Reference/Troubleshooting/User Safety on the UserDocumentation CD-ROM.Misfeed at Tray 1 (MPT)Follow these steps to clear the misfeed.1. Remove the jammed paper from Tray 1 (MPT).2. Push up the latch on the front of the printer to open Front Door A.6250-0136250-066

paper jams

jam at the fuser

jam at the duplex unit

Xerox Phaser 6250 Reference Manual

sided printing

binding preferences

PHASER 6250

printer tour

available configurations

front view

internal components

paper type

color settings

balance colors

calibrate margins

phaser 6250

service terms

symbols marked on the product

power source

general guidelines

servicing electrical components

regulatory specifications

declaration of conformity

Printer Introduction and Overview

general information

Printer Memory and RAM Capabilities

Parts of the Printer

Phaser 6250 Front Panel Configuration

Rear View

Image Processor Board

Routine Maintenance Items

Consumable Life Counter Behavior

Printer Specifications

Functional Specifications

Electrical Specifications

Media and Tray Specifications

Overview of the Phaser 6250 Color Laser Printer Theory of Operation

Print Modes

Selective Control; Paper Pick

LED Light Density CTD (ADC) Control of Sensor

Color Registration Control

Transfer Roller Assembly Control

Toner Control

Fuser Control

Paper Path of the Printer

Paper Path Route

Frame and Drive Assemblies

Main Drive Assembly - Transmission Route

Gear Layout - Print Engine and Tray 1

Paper Tray 2

Paper Feed - Tray 2

HCF Drive and Gears - Transmission Route

Sheet Feeder Drive and Gears - Transmission Route

Retard Housing Assembly

Chute Assembly In

Chute Assembly Out

Chute Assembly Exit

Duplex Motor Drive and Gear - Transmission Route

Chute Assembly Registration (REGI)

Transfer Roller and Fuser Assembly

Fuser Drive Assembly - Transmission Route

Xerographics

Imaging Unit Charge Voltage Contacts

Toner Cartridge Assembly

Toner Cartridge Assembly - cont'd

Toner Motor Drive Assembly - Transmission Route

ac switch harness assembly

error messages

Printer Status Codes

servicing instructions

Using the Troubleshooting Procedures

Voltage Measurements

service diagnostics

Service Diagnostic Front Panel Button Descriptions

Diagnostic Menu Map

Service Diagnostic Tests

error messages and codes

Jam History Error Codes Table

Error Messages and Codes Summary Table

Media Mismatch Errors

jam errors

Jam at Duplex: Jam D

Jam at Registration Roller: Jam RR

Misfeed at Tray 1 (MPT): Jam T1

Misfeed at Tray 2: Jam T2

Misfeed at Tray 3: Jam T3

Misfeed at Tray 4: Jam T4

Close Front Door

Install or Reseat Imaging Unit

Imaging Unit is Near End of Life

Install or Reseat Transfer Roller

Transfer Roller is at End of Life

Install or Reseat Fuser

Replace Fuser or Fuser is Near End of Life

Install or Lock [Y] [M] [C] [K] Toner Cartridge

Dusty Density Sensor

Output Tray is Full, Unload Paper

Remove Ribbon from [Y] [M] [C] [K] Toner Cartridge

Insert Tray [2] or Tray [2] Missing

Insert Tray [3] [4] or Tray [3] [4] Missing

tray 2 paper is low

Tray [3] [4] Paper is Low

Out of Paper; Load Tray 1 (MPT) with [size] [type]

sheet feeder

connections and ip address

connection setup

cleaning the outside of the printer

cleaning the density sensor

supported papers

basic printing

print quality

supplies info

front panel buttons

information pages

more information

printer management software

using printer management features

novell netware

novell netware troubleshooting

unpack printer

connect power

toner cartridge

imaging unit

transfer roller

feed roller kit

adding memory

internal hard drive

repacking instructions

printer settings

accessing power saver

accessing protected mode

accessing load paper timeout

adjusting front panel brightness

changing printer language

adjusting printing options

managing your printer

quick install steps

additional resources

service manual

phaser 6250 color printer

printer introduction and overview

printer memory and ram capabilities

parts of the printer

phaser 6250 front panel configuration

rear view

image processor board

consumable life counter behavior

printer specifications

functional specifications

electrical specifications

media and tray specifications

printer theory of operation

print modes

laser light intensity control

led light density ctd (adc) control of sensor

color registration control

transfer roller assembly control

toner control

fuser control

paper path of the printer

paper path route

major assemblies and functions

main drive assembly - transmission route

gear layout - print engine and tray

paper tray 2

paper feed - tray

hcf drive and gears - transmission route

sheet feeder drive and gears - transmission route

retard housing assembly

chute assembly in

chute assembly out

chute assembly exit

duplex motor drive and gear - transmission route

chute assembly registration (regi)

transfer roller and fuser assembly

fuser drive assembly - transmission route

imaging unit charge voltage contacts

toner cartridge assembly

toner cartridge assembly - cont'd

developer assembly transmission route

using the troubleshooting procedures

voltage measurements

service diagnostic front panel button descriptions

diagnostic menu map

service diagnostic tests

jam history error codes table

error messages and codes summary table

jam at fuser: jam f

jam at duplex: jam d

jam at registration

jam at registration roller: jam rr

misfeed at tray 1 (mpt): jam t

misfeed at tray 2: jam t

misfeed at tray 3: jam t

misfeed at tray 4: jam t

close front door

consumable errors

imaging unit is near end of life