12 YASKAWA ELECTRIC TOBPC73060034A Potentiometer Technical Manual5 Installation Procedure5 Installation Procedure◆ Section SafetyDANGERElectrical Shock HazardDisconnect all power to the drive, before servicing.Failure to comply will result in death or serious injury.Wait at least one minute after all indicators are off. The drivehas internal capacitors that remain charged even after the optionis disconnected. The drive charge LED will extinguish whenthe DC bus voltage is below 50Vdc. Measure drive DC busvoltage to confirm safe level.NOTICEDamage to EquipmentProperly connect the connectors.Failure to comply may prevent proper operation and possiblydamage equipment.

PREFACE AND SAFETY

RECEIVING

PRODUCT OVERVIEW

OPTION COMPONENTS

INSTALLATION PROCEDURE

OPERATING INSTRUCTIONS

RELATED DRIVE PARAMETERS

TROUBLESHOOTING

OPTION SPECIFICATIONS

YASKAWA LOCATIONS

REVISION HISTORY

YASKAWA j1000 Technical Manual

i.1 Preface

Terms and Abbreviations

i.2 General Safety

Safety Messages

Drive Label Warnings

Warranty Information

Quick Reference

Section Safety

Model Number and Nameplate Check

Drive Models

Component Names

Front Views

MECHANICAL INSTALLATION

Installation Orientation and Spacing

Removing and Attaching the Protective Covers

ELECTRICAL INSTALLATION

Standard Connection Diagram

Main Circuit Connection Diagram

Terminal Block Configuration

Protective Covers

Main Circuit Wiring

Main Circuit Terminal Power Supply and Motor Wiring

Control Circuit Wiring

Control Circuit Terminal Block Functions

Terminal Configuration

Wiring Procedure

I/O Connections

Main Frequency Reference

Braking Resistor

Interlocking with Connected Machinery

Using the Digital LED Operator

Digital Text Display

LED Screen Displays

Menu Structure for Digital LED Operator

The Drive and Programming Modes

Changing Parameter Settings or Values

Verifying Parameter Changes: Verify Menu

Switching Between LOCAL and REMOTE

Parameters Available in the Setup Group

Start-up Flowcharts

Basic Operation

Run Command Input Selection: b1-02

Stopping Method Selection: b1-03

Acceleration/Deceleration: C1-01 to C1-04

C6-02

Multi-Step Speed Operation (4-Step Speed)

Drive Input Voltage Setting: E1-01

V/f Pattern Settings: E1-04 to E1-10

Motor Parameters: E2-01 to E2-03

Analog Outputs: H4-01 to H4-03

Motor Protection: L1-01 and L1-02

Notes on Controlling the Brake for the Hoist Application

Drive Status Monitors: U1-01 to U4-13

Powering Up the Drive

No-Load Operation Test Run

Test Run with Load Connected

Verifying and Backing Up Parameter Settings

Motor Performance Fine Tuning

Drive Alarms, Faults, and Errors

Alarm and Error Displays

Fault Detection

Alarm Detection

Operator Programming Errors

Diagnosing and Resetting Faults

Fault Reset Methods

Troubleshooting without Fault Display

PERIODIC INSPECTION & MAINTENANCE

Inspection

Recommended Periodic Inspection

Periodic Maintenance

Drive Cooling Fans

PERIPHERAL DEVICES & OPTIONS

Peripheral Devices

Connecting Peripheral Devices

Installing Peripheral Devices

Installing a Leakage Breaker

Connecting an AC or DC Reactor

Connecting a Surge Absorber

Zero-Phase Reactor

Installing Fuses on the Input Side

Communication Options

A. SPECIFICATIONS

A.1 Heavy Duty and Normal Duty Ratings

A.2 Single/Three-Phase 200 V Class Drive

A.3 Three-Phase 400 V Class Drives

J1000 CIMR-JC series

YASKAWA ELECTRIC SIEP C710606 31B YASKAWA AC Drive – J1000 Technical Manual http://nicontrols.com

Exterior and Mounting Dimensions

Wiring Checklist

START-UP PROGRAMMING & OPERATION

LO/RE LED and RUN LED Indications

Start-up Flowchart

Test Run Checklist

PARAMETER DETAILS

A: Initialization

b: Application

b2: DC Injection Braking

C: Tuning

C2: S-Curve Characteristics

C4: Torque Compensation

d: Reference Settings

d2: Frequency Upper/Lower Limits

d3: Jump Frequency

d4: Frequency Hold Function

E: Motor Parameters

E2: Motor 1 Parameters

H: Terminal Functions

H2: Multi-Function Output

H3: Analog Input Terminal A1 Settings

H4: Multi-Function Analog Output Terminal AM

H5: MEMOBUS/Modbus Serial Communication

L: Protection Functions

L2: Momentary Power Loss Ride-Thru

L3: Stall Prevention

L4: Speed Agree

L5: Fault Restart

L8: Hardware Protection

n: Special Adjustments

o: Operator Related Settings

o3: Copy Function

o4: Maintenance Monitor Settings

U: Monitor Parameters

Cooling Fan Replacement

Safety Instructions and General Warnings

Mechanical Installation

Electrical Installation

Keypad Operation

Start Up

Parameter Table

Troubleshooting

SAFETY INSTRUCTIONS AND GENERAL WARNINGS

KEYPAD OPERATION

PARAMETER TABLE

INSTRUCTIONS FOR UL AND CUL

wiring diagram

SPECIFICATIONS

GENERAL SAFETY

ABOUT THIS OPTION

EXTERNAL HEATSINK OPTION INSTALLATION PROCEDURE

INSTALLATION PROCEDURE BY DRIVE MODEL

AI-V3/J