Yaesu FTM-400DE Quick Manual

Also see for FTM-400DE: Manual Instruction manual Instruction manual Quick start guide Firmware Update Instruction Manual

Yaesu FTM-400DE Quick Manual Manual pdf 1 page image

Switch to the operating band by touching the frequencydisplay on the screen, orpressing the [DIAL] knobon the right side of theoperating band.Tune in the frequency to be saved in the memory and pressthe key for one second or longer on the frequencydisplay screen.Touch on the screen for one second or longer todisplay the memory list.Press the [DIAL] knob or touch the frequency display onthe screen on the operating side and the MHz digits willblink. The frequency can then be adjusted in 1 MHz stepsfor a few seconds.Press the [DIAL] knob for one second or longer to displayonly the MHz digits. The frequency can then be adjusted in5 MHz steps for a few seconds.An empty memory channel willbe selected and displayedautomatically.To write the desired frequency tothe selected memory channelnumber, press the [DIAL] knobat the top right of the screen ortouch the screen directly toselect the memory channel.When the key is pressed,memory writing will end and thememory channel and frequencywill appear in the display.Press the key on the frequency display screen. Thefunction keys will be displayed under the operating band.Touch or on the screen to switch the display andselect the desired function.The band scope switches on or off each time istouched on the screen.The display bandwidth of the band scope is either ±25frequency steps (for wideband) or ±12 frequency steps (fornarrowband).Touch the screen, or turn the [DIAL] knob at the top rightof the screen to select the memory channel.After entering the name on the character input screen, pressthe key for one second or longer, and touch to returnto the memory list. Press the key again to return to theprevious screen.These keys can be substituted by the four operation keys normallydisplayed at the lower part of the frequency display screen (referto the operating manual for details).* is displayed on when the optional voice unit FVS-2 is installed.The function key will disappear and the display returns to theprevious screen when key is pressed again.Normally use the auto mode (AMS).Switch the Band A mode manually by pressing the key.Press the key for onesecond or longer and thentouch in the SETUPMENU screen.Touch on the screen andfollow the same process as the inputprocedure to change the call sign orname (moving the cursor to the leftend using and and touchingwill return the display to theprevious screen without the changebeing reflected). Press the keyto return to the frequency screen.After entering the call sign or name,by touching the characters on thescreen, or turning and pressing the[DIAL] knob at the top right ofthe screen, touch on the screento confirm and enter the call sign.Using the AMS (Automatic Mode Select) function, the transceivercan switch its communication mode automatically to match thereceived signal. This is very convenient because there is no need topay attention to the communication mode of the partner. Turn on theAMS function during normal operation. When the AMS function isactive, a bar will be displayed on top of the mode (Example: ).In the AMS mode, transmission and reception is carried out usingthe normal DN mode. However, when transmitting after receiving inother modes, the mode last received will be used. To transmit usingthe normal DN mode, touch the key and set the AMS functionagain. When operating using the digital fixed mode ( / ), try to beaware of the FM signal status and do not transmit when there is apossibility of interfering with the FM signals on the channel.FTM-400DR/DEQuick GuideVFOmodeMemorymodeUsing the band scopeSaving to a memory channelAssign a name to the memorySwitching the operating band108 to 137MHz (air band)137 to 174MHz (144MHz band)174 to 400MHz400 to 480MHz (430MHz band)480 to 999.99MHzSKIP/SELOFF D WTx PWRH ISCAN REVFW DBACKFW DBACKBEACONBACK FW DS.LIST MSGLO GHOMEBEACONTXBACK FW DREC PLAY TRACKAL L PLAY STOPCLR VOICEDWN UP12345 6 7 8 910 11MicrophoneaperturePTTVolume knobsBand A (digital/analog)Transmit band; white charactersBand B (analog)Sub-band; gray charactersDial knobs for frequency,memory channel and squelch setting5 Band A communication modeswitch / WIRES-X key1 Power switch / Lock key4 GM operation key2 DISP switch / SET mode key6 VFO / memory mode switch-over keyMemory edit key7 SQL key (touch the key then adjust usingthe DIAL knob)8 Mute key3 Function key / MW key9 Band scope key10 DATA terminal11 microSD memory card slotENTReception frequency bandsof Bands A & B NORMAL WIDERX COVERAGE settings(Default)OOOOOOO---M WFM WFM WFM WFM WFDisplaying the function keysSCOPE5MHzstepsInput / change call sign or nameENTCALLSIGNSETUPDISPBACKM WFM WFM/V M WFM WFPress for onesecond or longerSelecting the communication modeAnalogDigital High-quality voiceAuto Automatic mode operation using the AMS functionSETUPDISPCHANGEC4FM FDMA Digital basic mode.High-quality voice communication mode using the full12.5 kHz bandwidth.High-speed data communication mode that uses the full12.5 kHz bandwidth for data communication. The modeautomatically switches to this mode for picturecommunication.Conventional FM mode that uses the 25 kHz FM mode.::::Enter a call sign or name whenusing the FTM-400DR/DE forthe first time after purchase, orafter a factory reset is carriedout.The call sign or name enteredcan be changed any time.Digital communication between fellow C4FM digitalamateur transceivers and also communication with FMamateur transceivers are possible.Frequency operationsEH034M551communication (digital)Panel key Touch keyBACK FW DM/V M UTE SCOPES QLNOISESQL DTMFTouch the blinking [CALLSIGN] onthe screen to begin inputting the callsign (the display will switch to thecharacter input screen automaticallyif there are no operations for about 3seconds).

/ 2

Related manuals for Yaesu FTM-400DE