Yamaha BD-S1065 Owner's Manual

Also see for BD-S1065: Release note Owner's manual Owner's manual

Contents

Settings31 EnSETTINGS4 EnglishHDMI Video OutThis sets the resolution of the HDMI video output.Some TV are not fully compatible with the Blu-ray discplayer, which may cause the image distortion. In this case,press VIDEO-RESET on the remote control for fiveseconds. “HDMI Video Out” will be reset to “Auto”(factory preset value).Auto*, 1080p, 1080i, 720p, 480pNote– When the BD player is connected to a 1080p/24Hzcompatible TV and the “HDMI Video Out” is set to“Auto”, 1080p/24Hz will automatically be displayedwhen compatible discs are played back.At 1080p/24Hz or 1080p/60Hz, there is no outputfrom the COMPONENT jacks and VIDEO jack.Video Out SelectDual video output is possible simultaneously from theanalog video jacks (component, S-video, and video) andthe HDMI terminal with the following settings. Select thevideo output which you want to have priority according tothe following chart.Notes– 1080p is only available in HDMI.*1 Some discs prohibit high definition video output fromCOMPONENT jacks. In this case, video resolution is converted to480p (when “Video Out Select” is set to “Component”) or 480i(when “Video Out Select” is set to “HDMI”).*2 Depends on the TV connected. No video output when 1080psignal is output from the HDMI terminal.*3 No video output when 1080p signal is output from the HDMIterminal.– If the video equipment connected to each of theterminals is not compatible with the resolution of thepriority video output, abnormalities in images on thescreen may appear.Hint– This function can also be performed by the frontpanel buttons. Press and hold and on thefront panel (or press and hold DIMMER on theremote control) for more than 4 seconds while nodisc is inserted in this Player and the disc tray isclosed.Secondary AudioYou can turn on and off the audio of the picture in pictureor audio commentaries.– Select “On” to output the audio of the picture inpicture.– Select “Off” to enjoy the high-quality sounds of BD-Video.Hint– When you set “Secondary Audio” to “Off”, this unitdoes not output the clicking sound on the menu.On, Off*Audio OutYou can set the audio output suited for your playbackenvironment.1 Select the audio output connected to a TV or AVreceiver.2 Select the output mode.When you selected “HDMI Output”HDMI*: Select this to give priority to HDMI output. You canset the resolution of the HDMI video output in“Settings” - “Audio Video Settings” - “HDMI VideoOut”. (See page 31.)Component: Select this to give priority to analog (component, S-video, and video) output. You can set the resolutionof the component video output in “Settings” -“Audio Video Settings” - “Component Video Out”.(See page 30.)Settings on this Player Output ResolutionVideo OutSelectHDMI VideoOutComponentOut S/CVBS OutHDMI Auto *1 *2 480i *31080p No Output No Output1080i 1080i *1 480i720p 720p *1 480i480p 480p *1 480iSettings on this Player Output ResolutionVideo OutSelectComponentVideo Out HDMI Out S/CVBS OutComponent 1080i *1 1080i *1 480i720p *1 720p *1 480i480p 480p 480i480i 480i 480iHDMI Output*: Select this when you connect using HDMIterminal.Digital Output: Select this when you connect using DIGITALOUT terminal (COAXIAL/OPTICAL).7.1ch AudioOutput:Select this when you connect using AUDIO OUT(8ch discrete) jacks.2ch AudioOutput:Select this when you do not use SURROUNDsound equipment.Bitstream*: – Select this when connecting to HDMIequipment with a built-in decoder for DOLBYDIGITAL, etc.– Setting to Bitstream will output each audiosignal by Bitstream.PCM (Surround): – Select this when connecting to multi-channelHDMI equipment (without a built-in decoderfor DOLBY DIGITAL, etc.) or 2ch HDMIequipment such as TV.– Setting to PCM (Surround) will output byLINEAR PCM by decoding audio signalsrecorded in each audio output mode such asDOLBY DIGITAL, DTS.