Yamaha HAF3-S18 Owner's Manual
Thank you for choosing this Yamaha product.Please read this manual carefully before using it in a speaker installation.Keep the manual in safe place for future reference.Installation Instructions1. Flip the speakers upside down. Remove the existingspeaker screws.2. Determine the splay angle of the speaker and the holes touse on the front joiner plate.3. Install a rear joiner plate on the rear inserts of the clusterwith the provided screws and flat washers. Install an angleindicator plate on the front inserts using the correspondingholes for the appropriate splay angles with the screws andflat washers. Tighten permanently.4. Carefully flip the assembly to expose the top of thespeakers.5. Install a rear joiner plate on the rear inserts of the clusterwith the provided screw and flat washer on the centerspeaker and the two eye bolts on the side speakers. Installan angle indicator plate on the front inserts using thecorresponding holes for the appropriate splay angles withthe screws and flat washers on the center speaker and thetwo eye bolts on the side speakers. Tighten permanently.6. Use the two eye bolts on the rear of the speaker cluster andthe two eye bolts on the front to suspend the speakercluster.7. For steep tilt angles, move the rear eye bolts to the rearbottom insert of the speaker cluster and use as a pull backpoint. Make sure to replace the eye bolts with the providedscrews and washers.HAF3-S18(W)ARRAY FRAMEDimensions• Use only the eye bolts included with the speaker unit.• For information on load limits and the strength of the eyebolt,refer to the owner's manual of the speaker.Package ContentsHAF3-S18(W)❒ 3-1171 Angle indicator plates (2 pcs.)❒ 3-1174 Rear joiner plate (2 pcs.)❒ 3-0235 M10-40mm button head socket screws (14 pcs.)❒ 2-1432 M10 flat washers (16 pcs.)❒ 3-0112 M10 L-key wrench (1 pc.)NOTEOwner’s ManualEN PRECAUTIONSAlways follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the deviceor other property. These precautions include, but are not limited to, the following:• Before doing any installation or construction work, consult with an installation expert.• Make sure that the surface this bracket is being mounted on has the strength to handle the weight of both the speaker and thisbracket.• Use bolts and nuts as well as washers for installation and tighten them firmly so that the speaker is secure and does not move.• Always loosen the corresponding screw before adjusting the angle or direction of the speaker. Never force this adjustment withthe screw still tightened.• Some fittings may deteriorate over extended periods of time due to wear and/or corrosion. For optimum safety, the installationshould be checked thoroughly at regular intervals.Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure orimproper installation.* Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation.* Company names and product names herein are trademarks or registered trademarks of their respective companies.* Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right tochange or modify products or specifications at any time without prior notice. Since specifications, equipment or options maynot be the same in every locale, please check with your Yamaha dealer.CAUTIONPLEASE READ CAREFULLY BEFORE PROCEEDING* Please keep this manual in a safe place for future reference.3-1171 Angle Indicator Plate3-1174 Rear Joiner Plate3090Angle Indicator Plate(3-1171)[2X]M10 EyeBolt [4X]M10 Flat Washer [TYP] Rear Joiner Plate(3-1174)[2X]M10 Screw [TYP].406 DIA X 30 SLOT 2X.53 2X .4023.7637.6840.4720.7549.487.736.78.402 28X90 Maximun Splay ConfigurationTight Pack Configuration |
Related manuals for Yamaha HAF3-S18
manualsdatabase
Your AI-powered manual search engine