Zander Aachen SR3E Operating Instructions Manual
H. ZANDER GmbH & Co. KG • Am Gut Wolf 15 • 52070 Aachen • GermanyTel +49 (0)241 9105010 • Fax +49 (0)241 91050138 • info@zander-aachen.de • www.zander-aachen.de1Safety Relay for Elevators SR3EN03Ver. AE61-421-00Operating Instructions English translationErrors and technical changes reserved Automatic or manual start Short-circuit monitoring and ground faultt monitoring Up to PL e, SILCL 3, category 4(EN ISO 13849-1 / EN 62061 / EN 61508)Correct Use SR3E is an all-purpose emergency stop device with three saferelay contacts for safe monitoring of one or two channel sensors.The SR3E is specially designed for the use as safety componentin elevators according to EN 81-20 and EN 81-50, certified byTÜV Rheinland.Further applications for the SR3E include single or dual-channelemergency stop circuits and guard monitoring on machines andplants according to EN ISO 13849-1, EN 62061 and EN 61508. 3 non-delayed safety contacts1 non-delayed auxiliary contact Connection of:- Emergency stop buttons- Mechanical Safety switches- Non-contact safety switches- Safety components with OSSD-Outputs Control: single or dual channel Feedback loop for external contactors or extensionmodules Cyclical monitoring of the output contacts LED indicator for power and statusFunction The safety relay SR3E is designed for isolation of safety circuits according to EN 60204-1, stop-category 0 and can be usedin safety-related applications up to safety category 4, PL e (EN ISO 13849-1) SILCL 3 (EN 62061 / EN 61508) and as a safe-ty component in elevators according EN 81-20.ElectricalConnection A safety transformer according to EN 61558-2-6 or apower supply unit with electrical isolation from the mainsmust be connected Observe the instructions in the section “Tech. Data” If the device does not function after commissioning, itmust be returned to the manufacturer unopened. Open-ing the device will void the warranty The auxiliary contact 41-42 may not be used as a safetycontact Use adequate protective circuit for inductive loads (e.g.free-wheeling diode)Installation As per EN 60204-1, the device is intended for installationin control cabinets with a minimum degree of protection ofIP54. The following should be noted: Mounting on 35 mm rail according to EN 60715 Ensure sufficient heat dissipation in the control cabinet Minimum distance to adjacent devices according to thetotal current limit curveSafetyPrecautionsFig. 1 Block diagram SR3EFig. 3 Mounting / DemountingFig. 4 TerminalsA1: Power supplyA2 : Power supplyS11: Control voltageS10: Control lineS21: Start control lineS13: Control lineS14: Control lineS12: Control line13-14: Safety contact 123-24: Safety contact 233-34: Safety contact 341-42: Auxiliary contactto the device. It is not allowed to open the device, tamper with thedevice or bypass the safety devices. All relevant safety regulations and standards are to beobserved. The overall concept of the control system in which thedevice is incorporated must be validated by the user. Failure to observe the safety regulations can result indeath, serious injury and serious damage. Note down the version of the product (see label “Ver.”)and check it prior to every commissioning of a new de-vice. If the version has changed, the overall concept ofthe control system in which the device is incorporatedmust be validated again by the user. Installation and commissioning of the device must beperformed only by authorized personnel and who hasread and understood this operating instructions. Observe the country-specific regulations when installingthe device. The electrical connection of the device is only allowed tobe made with the device isolated. The wiring of the device must comply with the instruc-tions in this operating instructions, otherwise there is arisk that the safety function will be lost. It is not allowed to open the device, tamper with thedevice or bypass the safety devices. The contact protection and the insulation of the supplycables must be designed for the highest voltageFig. 2 State diagram for SR3E with manual start |
Related manuals for Zander Aachen 472292
Zander Aachen SR3C Operating Instructions Manual
Zander Aachen SR7C Operating Instructions Manual
Zander Aachen SR4C Operating Instructions Manual
Zander Aachen MINOS SD1E Operating Instructions Manual
Zander Aachen SR7D User Manual
Zander Aachen SR7D User Manual
Zander Aachen SR2C Quick Start Manual
Zander Aachen SR3D User Information
Zander Aachen SR3D User Information
Zander Aachen SR3C User Information
manualsdatabase
Your AI-powered manual search engine