Zenith H25E37Y Installation And Operating Manual, Warranty

P A G E 3 0 206-3683Installer Menus00 FACT MENU (Factory Mode)Used to access and customize the 00 - 24 Installer’s Menu settingsusing installer type remotes.01 PRESET PX (Preset Picture)Saves your custom video settings (color, tint, contrast, and bright-ness) in nonvolatile memory (not affected by power loss). Memorystatus is indicated by a 1 for “custom settings already stored,” or0 for “custom settings have not been stored.”Make all custom video settings before you access the Installer’sMenu and PRESET PX. When you use the ADJUST keys to togglefrom 0 - 1, any changes in the video settings will be stored surethey are correct! These settings become the PRESET values for thePICTURE PREF option of the Video Menu. (For more informationrefer to the Video Menu section of this manual.)02 PRESET AXThese TVs are monaural audio only. Since monaural operation isonly mode available, leave default setting.03 POWER MANAGE (Power Management)The POWER MANAGE function is for saving energy. When set to 0,Power Manage is OFF. Settings range from 0 - 7, with 1 - 7 repre-senting the hours that the TV will remain on, unless there hasbeen activity from either the control panel or remote.04 VERT POS (Vertical Position)Moves captions and displays vertically on the screen. Use theADJUST keys. Typical value is 15. Black bars top and bottomdefine the active screen area.05 HORZ POS (Horizontal Position)Moves captions and displays horizontally on the screen. Use theADJUST keys. Typical value is 15. Black bars top and bottomdefine the active screen area.06 BAND/AFC (Band/Automatic Frequency Control)There are 8 possible settings for this option:0 = Broadcast Fixed 4 = Broadcast AFC5 = CATV Fixed 1 = CATV AFC6 = HRC Fixed 2 = HRC AFC7 = ICC Fixed 3 = ICC AFCChannels are accessed faster when fixed modes are used. The AFC(search modes) should only be used when some channels are noton nominal frequencies. NOTE: BAND is automatically set by AUTOPROGRAM.If some channels were not found by AUTO PROGRAM, select theappropriate AFC setting here and add the channels using theADD/DEL option in the Setup Menu.07 MIN VOLUME (Minimum Volume)This function determines the minimum volume level allowable withthe VOLUME (VOL) Up/Down control. In this way, for example,someone cannot set the volume too low to hear. The range is from0 to 63—change values with ADJUST . The factory default is 0,which provides full range of volume control. It may be best to setthe same value on every TV. NOTE: The minimum volume level can-not have a value setting higher than in the MAX VOLUME level(described below).08 MAX VOLUME (Maximum Volume)This function determines the maximum volume level allowable withthe VOLUME VOL Up/Down control. In this way, for example, some-one cannot set the volume level high enough to disturb others.The range is 0 to 63, with 63 as the default which gives the guestthe full range of volume control. Change values with ADJUST keys.It may be best to set the same value on every TV. NOTE: The maxi-mum volume level cannot have a value setting lower than the MINVOLUME level (described above).09 AC ON (AC Power Switchable)Allows the TV to turn ON just by applying AC power. Pressing theON button is not necessary. This is desirable when the TV isplugged into a cable box or a power outlet controlled by a wallswitch. Use ADJUST to select 0 or 1, where 0 is the default is OFF,and 1 is ON.NOTE: When set to 1 (ON), the TV does not respond to ON/OFFcommands from either the remote or the control panel, and theSLEEP TIMER is also nonfunctional.10 KEY DEFEAT (Keyboard Defeat)When set to 1, it prevents the end user from accessing screenmenus on the front panel—MENU, SELECT, and ADJUST do notfunction. When set to 0, those keys are functional. The menus canalways be accessed with MENU on the remote.11 STRT CHANNEL (Start Channel)When active, this function allows you to determine the initialchannel number when the TV is turned ON. This feature is usefulfor an in-house information channel, since the TV would alwaysselect that channel when it is turned on. Setting this to 255 caus-es the last channel viewed when TV was turned off to be the tunedto channel when the TV is turned on again.The range of values is 0 - 255. Use (adjust) keys to choose num-bers that determine the start channel.Use the Installer’s Menus to make TV operation adjustments