Zephyr Tornado II AK8200AS Use, Care And Installation Manual

Also see for Tornado II AK8200AS: Use, care and installation guide Use, care and installation guide

Contents

Important Safety Notice3WARNINGTO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.NOT FOR USE OVER AN OUTDOOR GRILLCAUTION7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJVattics, crawl spaces or garages.OPERATION$OZD\VOHDYHVDIHW\JULOOHVDQG¿OWHUVLQSODFH:LWKRXWWKHVHFRPSRQHQWVRSHUDWLQJEORZHUVFRXOGFDWFKRQWRKDLU¿QJHUVand loose clothing.The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due tonegligence and the warranty of the unit automatically expires due to improper maintenance.*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.ELECTRICAL REQUIREMENTSImportant:Observe all governing codes and ordinances.It is the customer’s responsibility: 7RFRQWDFWDTXDOL¿HGHOHFWULFDOLQVWDOOHU- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** andall local codes and ordinances.,IFRGHVSHUPLWDQGDVHSDUDWHJURXQGZLUHLVXVHGLWLVUHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFLDQGHWHUPLQHWKDWWKHground path is adequate.Do not ground to a gas pipe.&KHFNZLWKDTXDOL¿HGHOHFWULFLDQLI\RXDUHQRWVXUHWKHUDQJHKRRGLVSURSHUO\JURXQGHGDo not have a fuse in the neutral or ground circuit.*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuitprotected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer toElectrical Diagram on product.AK8200AS - 710W, 6 AmpsAK8300ASX (CBI-290B / CBI-600B) - 217W, 1.85 Amps / 460W, 3.85 AmpsAK8300ASX (PBI-1100A, PBN-1000A / CBE-1000) - 780W, 6.55 Amps / 840W, 7.3 Amps$FDEOHORFNLQJFRQQHFWRU QRWVXSSOLHG PLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWVSXUFKDVHand install appropriate connector if necessary.FEDERAL COMMUNICATION COMMISSION INTERFACE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, thereis no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one of the following measures:. Reorient or relocate the receiving antenna.. Increase the separation between the equipment and receiver.. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.. Consult the dealer or an experienced radio/TV technician for help