ebm-papst W1G115-AG03-07 Operating Instructions Manual

Contents

ebm-papst W1G115-AG03-07 Operating Instructions Manual Manual pdf 1 page image

Operating instructionsW1G115-AG03-07Translation of the original operating instructionsebm-papst Mulfingen GmbH & Co. KGBachmühle 2D-74673 MulfingenPhone +49 7938 81-0Fax +49 7938 81-110info1@de.ebmpapst.comwww.ebmpapst.comCONTENTS1. SAFETY REGULATIONS AND NOTES11. SAFETY REGULATIONS AND NOTESPlease read these operating instructions carefully before starting to workwith the device. Observe the following warnings to prevent malfunctionsor physical damage to both property and people.These operating instructions are to be regarded as part of this device.If the device is sold or transferred, the operating instructions mustaccompany it.These operating instructions may be duplicated and forwarded forinformation about potential dangers and their prevention.1.1 Levels of hazard warnings11.1 Levels of hazard warnings These operating instructions use the following hazard levels to indicatepotentially hazardous situations and important safety regulations:DANGERIndicates an imminently hazardous situation which, if notavoided, will result in death or serious injury. Compliance withthe measures is mandatory.WARNINGIndicates a potentially hazardous situation which, if not avoided,could result in death or serious injury. Exercise extremecaution while working.CAUTIONIndicates a potentially hazardous situation which, if not avoided,may result in minor or moderate injury or damage of property.NOTEA potentially harmful situation can occur and, if not avoided, canlead to property damage.1.2 Staff qualification11.2 Staff qualificationOnly specialised electrical personnel may install the device, perform thetest run and work on the electrical system.Only trained and authorised specialist personnel are permitted totransport, unpack, assemble, operate or maintain the device, or to use itin any other manner.1.3 Basic safety rules11.3 Basic safety rulesAny safety hazards stemming from the device must be re-evaluatedonce it is installed in the end device.Observe the following when working on the unit:; Do not make any modifications, additions or conversions to thedevice without the approval of ebm-papst.1.4 Electrical voltage11.4 Electrical voltage; Check the electrical equipment of the device at regular intervals, referto chapter 5.2 Safety test.; Replace loose connections and defective cables immediately.WARNINGTerminals and connections have voltage even with aunit that is shut offElectric shock→ Wait five minutes after disconnecting the voltage at all polesbefore opening the device.CAUTIONIf control voltage is applied or a speed setpoint is stored,the motor automatically restarts, e.g. after a power failure.Danger of injury21.5 Safety and protective functions21.6 Electromagnetic radiation21.7 Mechanical movement21.8 Emission21.9 Hot surface21.10 Transport21.11 Storage21.12 Disposal32. PROPER USE43. TECHNICAL DATA43.1 Graphic rendition of products53.2 Nominal data53.3 Technical description53.4 Mounting data53.5 Transport and storage conditions64. CONNECTION AND START-UP64.1 Connecting the mechanical system64.2 Connecting the electrical system64.3 Connection via plug64.4 Connection of the Hall IC74.5 Connection diagram84.6 Checking the connections84.7 Switch on device84.8 Switching off the device85. MAINTENANCE, MALFUNCTIONS, POSSIBLECAUSES AND REMEDIES95.1 Cleaning95.2 Safety testItem no.: 51080-5-9970 · Revision: 71954 · Print-out: 2012-02-24 · Y. Uhlmann (VM-TDO) · Page 1 / 9ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 7938 81-0 · Fax +49 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com