jablotron CA-1202 Athos Installation Instructions Manual
GSM car alarm CA-1202 „Athos“ 4/4 MHF5260510 SMS text editingThe SMS texts (alarm information and instructions) are factorypreprogrammed. However, it is possible to change these texts by amobile phone or via internet access www.GSMlink.czTo change a text by your mobile phone, send SMS:MASTER TXT zz,text,zz,text,…where: zz is the text index (see following table)text is your new text – up to 30 characters, full stop (dot) orcomma cannot be used in the text, spaces are allowedExample: MASTER TXT 01,LOCK PLEASEBy changing texts number 01 to 16, you will modify the control SMSinstructions. This allows you to customize the remote control of the car.You can also make your own password part of the instruction to increasethe security of the mobile phone remote access.10.1 SMS text tablezz Factory default text zz Factory default textSMS commands: 44 Wireless detector01 AM 45 Current detector02 DM 46 Telephone 103 IMO 47 Telephone 204 UNIMO 48 Telephone 305 STATUS 49 Telephone 406 HELP 50 Telephone - UC07 CREDIT 51 Telephone - MC08 DIAL 52 Remote controller09 HF Status information:10 LOCATOR 60 Car alarm reports:11 MC 61 Status:12 UC 62 Armed13 DIP 63 Disarmed14 TEL 64 Ignition key ON15 LEARN RC 65 Ignition key OFF16 LEARN JA 66 Engine is blocked17 SIREN 67 Engine is unblocked18 SET 68 No alarmEvents: 69 Alarm timeout30 Alarm 70 Low accumulator voltage31 Alarm canceled by a user 71 Power failure32 Fire alarm 72 Power recovery33 Tamper alarm 73 Time:34 Disarming 74 Low battery voltage35 Arming Confirmation SMS:36 Low battery voltage 80 Command accepted37 Engine is blocked 81 Command syntax error38 Engine is unblocked 82 New MC code:Source: 83 New UC code:40 Ignition key 84 Reset41 Door contact 85 Registered phone number:42 INP1 activation 86 Credit:43 INP2 activation 87 LEARN mode, enrolled11 Internet remote accessThe web site www.GSMLink.cz enables car alarm remote control (tousers) and setting (to installers). The following features are enabled:To get internet access to an installed and powered car alarm you willfirst be asked to register your car alarm on the first page. You will find aunique registration code for your car alarm on the warranty card.11.1 Reset GSMIf you need to disconnect and then reconnect the GSM module to theGSM network, then use the command “MASTER RESET GSM”.This does not affect any settings and is typically used for GPRSactivation or charging up credit. This command always requires theMaster code.12 Central monitoring station communicationThe GSM pager allows central monitoring via GPRS data protocol. Thecentral monitoring station (CMS) gets arming, disarming and alarminformation. It also regularly checks the communication link to the car after it isarmed. So if anyone tries to tamper with GSM pager communications, it willindicate an alarm at the CMS.13 Additional features13.1 Car battery low voltage reportingThe GSM pager checks the voltage of the car battery. If the voltage is toolow (10V) it will notify users via an SMS message. This avoids completedischarging of the car battery if you forget to turn off your lights etc.13.2 Back-up batteryThe car alarm can be backed up by a BB-01 battery. Thus, the car alarmcan keep sending information when the car battery is disconnected. Back uptime is provided for several hours. The manufacturer recommends regularBB-01 checking once a year. The battery should be replaced every two years.Low back-up battery voltage (below 4V) is reported to the user via SMS(change the battery in this case).13.3 Voltage drop detectorThe built-in voltage drop detector can trigger an alarm if an electricaldevice in the car is turned on while the car is armed. The sensor activates10 minutes after arming (if enabled).13.4 Entrance delay acoustic indicationThe siren can indicate arming and disarming by beeps (see DIPparameter setting). The siren will also indicate the triggering of a wirelessdetector which provides an entrance delay (by a single beep). This wayyou can be reminded not to forget to disarm your car alarm after youopen the garage door etc.13.5 Limited number of alarmsIf any sensor (input) repeatedly triggers alarms then this particular input willbe bypassed automatically after the third alarm (it will remain bypassed untilthe car alarm is disarmed).13.6 Car locationIf your GSM provider offers a location service, you have to activate theLOCATOR command after installation by the following SMS sequence:MASTER LOCATOR xx…xwhere: MASTER is installers codexx...x is provider’s sequence to obtain the position ofthe car alarm SIM card (check with your GSMprovider for details)After this sequence has been sent successfully once, the car alarmmemorizes the parameters and from this moment on you can obtain thelocation of the car by just sending the instruction LOCATOR.Note: GSM location service may not be available in some countries.13.7 Pre-paid SIM card balanceIt is recommended not to use prepaid cards in the car alarm. If you haveno other choice than prepaid cards, you can enable the CREDITinstruction by following sequence:MASTER CREDIT uuu..u xx yyy zzwhere: uuu…u is the provider’s code to obtain the balancexx is the time period (in days) for regular checkingyyy is the threshold level below which the balance isreported to the user (TEL1)zz is the position of the first digit of the balance in the replySMS from the provider• After this sequence has been sent once, the car alarm will check thebalance automatically every xx days and if the balance is lower thanyyy the user will be notified (TEL1)• If the CREDIT instruction is enabled in the above way, the user canalso obtain the current balance by the instruction CREDIT• To disable the automatic balance checking set the time period “xx” to 00.13.8 RoamingIf you travel abroad and your SIM card supports roaming, the car alarmwill work there too.13.9 Siren activationIf you are searching for a stolen car, you can operate the sirenremotely by the following SMS instructions:MASTER SIREN turns the siren on for 10 minutesMASTER SIREN ON siren on permanentlyMASTER SIREN OFF siren offTo avoid misuse of this option, only an installer can switch the siren on.13.10 LED indicator signalsLED state MeaningOFF Disarmedpermanently ON Connecting to a GSM network or a phone callRegular slow flashing ArmedRegular fast flashing Alarm memoryInterrupted light Car was stopped (immobilization)Flashing after ignition off GSM network is not available14 SpecificationPlease see Mode 3.GSM car alarm CA-1202 „Athos“ 1/4 MHF52605CA-1202 “Athos” installation manualMODE 2 – for cars with an original remote control for central lockingMain features for this mode:• Remote control of the alarm system via SMS instructions as wellas by the original remote control for central locking.• Sending of alarm SMS messages to up to 4 phones.• Dialing and acoustic alarm warning to up to 4 phones.• Location tracking of the car (using the triangulation feature of theGSM provider)• Central monitoring of the car when armed (fully supervised GPRSprotocol)• Remote immobilization of the car via SMS instruction.• Protecting a car with wired and wireless sensors (wireless sensors canalso be used to protect the garage where the car is parked).• Optional - Hands Free calling (receiving of any incoming call anddialing up to four pre-programmed phone numbers)• Remote internet alarm access (user and installer levels) viawww.GSMLink.cz1 Before installationThe CA-1202 should only be installed by a professional installer. Themanufacturer assumes no liability for damages caused by incorrectinstallation or use of this product.The Athos car alarm is suitable for cars with 12 V and negative grounding.The main unit is designed for installation in the passenger cabin.Disconnect the car battery before starting installation; study the carowner manual first. Avoid drilling into the metal parts of the car body.Note: Use only proper crimping tools and parts to make connections. Cutall unused wires and insulate them properly.The thin wire which leads directly out of the central unit is the remotecontrol and wireless detector antenna. The location of this wire affects thecommunication range. Place the antenna on a suitable plastic surface sothat the other wires do not screen it.2 Wiring• YELLOW – siren output (+12V / max. 1A).• GREY – door switch input. It reacts to connection or disconnectionfrom the ground (automatically recognizes logic).• WHITE – INP1 input – to confirm locking/unlocking of the car by theoriginal remote control by confirmation signal from the turn lights(flashers).• YELLOW–WHITE – INP2 alarm input – reacts to connection ordisconnection from the ground (automatically recognize logic).• BLUE – ignition key input (+12V). Be sure, that there is +12V whilethe key is on and while starting.• GREEN – LED indicator – install it in a visible spot on the dashboard.Connect the other end of this lead to the GND.• WHITE–BLACK (position 10) – “Lock“ WHITE–BLUE (position 11) –“Unlock” – control inputs for detecting locking and unlocking toactivate arming/disarming. They are usually connected to the outputsof the central locking control unit.. If these are not available, the caralarm inputs can be connected directly to the power wires of thecentral locking motors. Two pairs of central locking wires are available.For mode 2 use the wires with red shrinkable tube. Carefully pushthe ends of the chosen wires into the main plastic connector. Becareful to select the correct wires as removal from the main connectoris very difficult without the proper tool.• BLACK–GND – connect to the original grounding in the car.• RED – power supply +12V – connect directly to the battery. Checkthat the installation is properly finished and that the GSM antenna isconnected before powering up!• ORANGE – back-up battery – connect optional battery BB-01(Jablotron) if desired. If the BB-01 is not connected, then ground the wire.• 2x BROWN – immobilization circuit (8A permanently, max. 12A /3minutes).• Pink – not used3 SIM card insertion1. Make sure, that the PIN password on the SIM is disabled. You cando this using a mobile phone (e.g. for NOKIA: MENU, SETTINGS,SECURITY SETTINGS, PIN CODE REQUEST, OFF). If your SIM carddoes not allow switching the PIN off, change the PIN to 0000.2. Activate the SIM card if necessary (see provider’s instructions),ensure that it works (by a mobile phone) and record its phone number.3. Using a thin pointed tool, press the colored button to release the SIMcardholder. Insert the SIM card into the holder with the gold contactsfacing up and then reinsert the holder.4 GSM antenna installationDO NOT switch the power on before the GSM antenna is connected.The provided antenna is adhesive and should be attached to the car window.The antenna should not be obstructed by any metal part. It is recommend toinstall the antenna in a place where it is not easily visible (tinted part of thewindow, behind the mirror etc.). If the car has an original GSM antenna installed, itcan be used (if the connector is different, use an appropriate adapter).5 Initial powering-up of the alarmMake sure, that the GSM antenna is connected, SIM card inserted and thewire harness installed properly. Then connect the power (car battery). TheLED indicator will turn on and the siren will make a short chirp. Wait until theLED turns off (up to 1 minute).If the LED starts to flash, no GSM network was found. In such a case turn thepower off, remove the SIM card and try to use it in a mobile phone (at theplace where the GSM antenna is). Check also if the PIN protection is OFF (orset to 0000). If the SIM card logs into network successfully, reinsert it in to thealarm and repeat powering-up.After the alarm is powered, you have to:a) Select Mode 2 by command RESET EN 2b) Enroll remote controls and wireless detectors (if used)c) Set the programmable features (phone numbers, DIP, SET, etc.).These can be done by:• SMS instructions – see table 6.1. For example sending SMS: MASTERRESET EN 2 to the car alarm will select Mode 2.• Internet page: www.GSMlink.cz is the most convenient way. Toregister there you need to know the registration code (printed on thewarranty card) and the master code (factory default is MASTER).• SIM Card phone directory editing (see table 6.1 for list of featureswhich can be programmed this way). After the initial powering-up a list ofparameters is created in the SIM card phone directory. If you then insertthe SIM card in to a mobile phone, you can set particular features (byentering numbers to the created list). The entry for Mode setting is notautomatically created, but it is possible to make a new entry name:RESET EN and number: 2. Data entered this way are read by the caralarm after the SIM card is reinserted. For security reasons it is erasedafter reading.6 Enrollment of remote controls and detectorsUp to 4 RC-4x remote controllers and up to 8 JA-60 wireless detectors can beenrolled to the car alarm (after Mode 2 is selected by the RESET EN 2 instruction).Remote control enrollment:1. The car alarm should be disarmed, ignition on2. Send the SMS instruction: MASTER LEARN RC• The siren will chirp 3x and the LED will start flashing.3. Press and hold buttons and together for 3 sec on the remotecontrol.• A siren chirp confirms the enrolment.• By enrolling the first remote control all other remote controlspreviously enrolled will be erased (all the remote controls you want touse must be enrolled during the same enrolment session).4. Exit enrollment by turning the ignition off.Wireless detector enrollment:1. The car alarm should be disarmed, ignition on2. Send the SMS instruction: MASTER LEARN JA• The siren will chirp 3x and the LED will start flashing.3. Insert a battery in to the detector.• A siren chirp confirms the enrollment.• By enrolling the first detector all other detectors previously enrolledwill be erased (all the detectors you want to use must be enrolledduring the same enrollment session).4. Exit enrollment by turning the ignition off.Note: if the detector is switched to delay mode the alarm will provide a 20second entrance delay after triggering of the detector. An exit delay of 20seconds is provided to all enrolled detectors after the car alarm arming. |
Related manuals for jablotron CA-1202 Athos
jablotron CA-1802 ATHOS Installation Manual
jablotron CA-340 Installation Instructions Manual
jablotron CA-320 Installation Instructions Manual
jablotron CA-02 Fox Installation Instructions Manual
jablotron Athos Installation Manual
jablotron CA-1803BT Athos Installation Manual
jablotron CA-01 Pulse Instructions & Installation Manual
jablotron CA-10 REX Installation Manual
jablotron Athos CA-1202 User Manual
jablotron Athos CA-1202 User Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine