jablotron CA-1803BT Athos Installation Manual
Also see for CA-1803BT Athos: Installation manual
GSM car alarm CA-1803BT „Athos“ 1/6 MHF56603Installation manual: CA-1803BT “Athos” – mode 1for cars without an original remote control for central lockingMain features for this mode: Remote control of car central locking (if installed) via a remotecontrol. Sending alarm and information SMS messages to up to 4mobile phones. Dialling pre-programmed phone numbers during alarms andgiving an acoustic warning signal. Monitoring the vehicle‘s movement via GPS (GlobalPositioning System). Passing data to the central monitoring station. Remote immobilization of the car via SMS instructions. Remote control and programming of the alarm system from amobile phone. Securing the vehicle’s goods area and the garage via up to 8wireless detectors of the JA-8x series. Handsfree calling from the car and remotely listening-in to the car(receiving of any incoming calls and dialling up to 4 pre-programmed phone numbers). Extension of functions via the CR-11A module, for example,operating an independent car appliance via SMS (12V only). Internet access and configuration from the www.GSMLink.cz website.1. Before installationThe auto-alarm should only be installed by a professional installer. It issuitable for cars with a dashboard voltage supply of 12V or 24V with anegative ground connection. During the first power-up, the value of supplyvoltage is read and the inputs are set to default settings. The alarm isdesigned to be installed inside the car.The immobilizer relay contact of car alarm is connected only in disarmedmode and if the ignition is on. Do not block circuits that are under voltagewhile the ignition is off. It could cause a serious damage of the vehicle.Disconnect the car battery before starting installation. For airbag-equipped cars, no person is allowed to stay inside the car while handlingthe battery. Disconnecting the battery can cause a reset of some of thecar’s devices (e.g. clock, default settings etc.). Avoid drilling into the metalparts of the car body. The manufacturer is not responsible for damagecaused by any incorrect or unsuitable application of the product.For crimping, special purpose tools should be used. If you do not usesome of the cables, cut them off at a distance of 10cm from the connector,insulate them properly and tie them into a bunch.For cars with a voltage supply of 24V, the following restrictionsapply to car alarm installation:1. It is not possible to connect a hands-free set of type HF-03.2. When used for acoustic signalling, the SIR output is switched to thepower supply voltage. Consequently, this output switches to 24V, soit is necessary to use a siren of type SA-606-24V instead of thesiren which is supplied in the standard package. In this case it isnecessary to set the confirmation beeps to 100 ms.2. The wiringBefore installation, connect the wires as follows: Yellow – output siren – switches to +12V (24 V) / max. 1.3 A. Itsignals an alarm (30 sec) and confirms control signals1. Gray – door switch input. It reacts to connection or disconnectionfrom ground. These switches should be fitted to all of the car’s doors. White – input INP1 – alarm input. It reacts to a connection or adisconnection from the ground Yellow-white – input INP2 – alarm input. It reacts to a connection or adisconnection from the ground This input can trigger an alarm even ifdisarmed (24 hour reaction). Blue – signals that the ignition key is turned on. Reacts to +12V(24V) from the switch case. Make sure that a voltage is present in theconnecting wire while starting. Green – LED indicator – should be installed in a visible place on thedashboard. White-black (position 10) – “Lock”, White-blue (position 11) –„Unlock“ – Central locking control outputs. They switch to ground(max. 200mA) with a selectable pulse length. For MODE 1, a pair ofwires with black shrinkable tube should be put into the connector. Thewires are equipped with black isolation diodes which protect thefunctionality of cars with an intelligent central unit. Black – ground – connect to the original grounding point. Red – power supply +12V (24V) - connect directly to the battery. Thepower should be turned on only after a thorough check of the wholeinstallation has been made! Orange – back-up battery – connects to a back-up battery of type BB-02 (capacity 450 mAh, consumption up to 20 mA.) 2x Brown – immobilization circuit (max. 8A constantly, 12Aintermittently).1 this function is optional Pink – output AUX – an optional function of the output, see table 7 – thepower supply of external sensors is switched on by +12V/20mA or by buscommunication for modules CR-11AIt is possible to attach a hands-free set of type HF-032. Using this you are ableto phone out from the car via the car alarm, and also to remotely listen-in to thecar after an alarm has been triggered or after the car has been immobilized. TheHF set connects to the RJ connector on the front side of the car alarm unit.3. SIM card insertion1. Make sure, that the PIN number on the SIM is disabled. If the SIM carddoes not allow you to switch the PIN off, set the PIN to 0000. Remember(note down) the phone number of your SIM card. It is recommended todelete all original records in the SIM card’s phone directory.2. Insertion of the SIM card: using a thin object, press the yellow peg inorder to pull out the SIM card holder (the front side of the alarm), insert theSIM card into the casing with the conducting contacts facing up and pushthe casing back carefully.3. Install and attach the GSM antenna– (the car alarm must not be connectedto a power supply unless a GSM antenna is connected !!!). The antenna isequipped with an adhesive tape and has to be stuck onto the car’s window or toanother suitable place like, for instance, below the upper part of the dashboard.The antenna should not be installed close to the car alarm or near otherelectronic devices. It is recommended to install the antenna in a place where it isnot easily visible (preferably in a tinted part of the window). Clear and dry thespot carefully.4. Install provided GPS antenna - place the antenna so that it will not beshielded by metal parts of the car. It can be installed just under the top part of adashboard (turned with the black plastic cover upward) (the antenna can beshielded by plastic materials). Wrap both connectors using plastic sticky tape asthey are connected to GND.5. Check the wiring and connect the power supply. A flash of the indicator anda beep of the siren indicate that the device is being connected to the GSMnetwork. Wait until the indicator turns off (up to 1 minute). After that the caralarm is logged in to the GSM network.If the flash does not disappear within 1 minute, it means that the loginprocess failed. If such a case occurs, turn off the power supply, pull out theSIM card, ensure that the SIM contacts are clean, insert the card into amobile phone and check, whether a connection can be established in thatparticular place. Also make sure that the SIM card‘s PIN is turned off (or thatit is set to 0000). If the mobile phone connection check is successful, returnthe SIM card to the car alarm and repeat the whole procedure.4. After turning the power supply onIn order to use the functionality of the car alarm according to your needs you firsthave to setup its logic and behaviour by the RESET command. Subsequently,phone numbers and other optional parameters should be set up and an RC-8x keyfob should be enrolled. The setup can be done in the following ways: by editing a record in the SIM card phone directory (it is the simplestsetting method but limited to some functions only, see table 5.1). These settings(which determine the devices‘ behaviour) are read from the SIM card after eachpowering up of the car alarm. After the initial powering up of the new car alarmwith a new (blank) SIM card, configuration records (names) are created in theSIM card’s phone directory and the default values set. But in the case that thealarm had been set before and a new (blank) SIM card is then inserted, then thestored parameters are copied from the internal memory to the SIM card. Thiswill help you after SIM card changing. You can perform basic settings of some ofthe car alarm’s functions by pulling the SIM card out of the alarm (after thepower supply has been disconnected) and subsequently inserting it into amobile phone where you assign numbers to the names of functions displayed inthe phone directory from the SIM. See table 5.1 for setting the car alarm’soptional parameters. Settings from the SIM card are read after its insertion andpowering up.2 these accessories are optional |
Related manuals for jablotron CA-1803BT Athos
jablotron CA-1802 ATHOS Installation Manual
jablotron Athos Installation Manual
jablotron CA-1202 Athos Installation Instructions Manual
jablotron CA-10 REX Installation Manual
jablotron CA-340 Installation Instructions Manual
jablotron CA-320 Installation Instructions Manual
jablotron Athos CA-1802 User Manual
jablotron CA-1802 athos User Manual
jablotron Athos CA-1802 User Manual
jablotron CA-02 Fox Installation Instructions Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine