Ultimaker 2 Extended manuals
2 Extended
Table of contents
- Table Of Contents
- A. Welcome to the Ultimaker 2
- A2. Specifications of the Ultimaker 2
- B. Get started and unpack your Ultimaker 2
- B2. What's in the box
- B3. Ultimaker 2 at a Glance
- C. Installing parts on your Ultimaker 2
- C2. Spool holder and filament guide
- C3. Switch on/off the Ultimaker 2
- D. First use of your Ultimaker 2
- D2. Leveling the build plate
- D3. Loading filament material
- D4. Make your first 3D print
- D5. 3D Printing and print removal
- E. Make a print file with Cura software
- E2. Cura software interface
- E3. From YouMagine.com to load file in Cura
- E4. Preparing a 3D model
- E5. From SD-card to print your file
- F. Maintenance for your Ultimaker 2
- F2. The glass plate
- F3. Change filament and material feeder
- F4. Lubricating the axes
- G. Troubleshooting and support for the Ultimaker 2
- G2. Contact support
- G3. Terminology
- G4. Safety and Compliance
- Terms of service
2 Extended
Table of contents
- Table Of Contents
- WELCOME TO THE ULTIMAKER 2
- Safety and compliance
- Specifications
- SETTING UP THE ULTIMAKER 2
- What's in the box
- Ultimaker 2 at a glance
- Installing accessories
- GETTING STARTED
- Configuration wizard
- Start a print
- ADVANCED PRINTING OPTIONS
- Cura
- Display and controller
- MAINTENANCE & SUPPORT
- Maintenance
- Troubleshooting
- Support
2 Extended
Table of contents
- Table Of Contents
- SAFETY AND COMPLIANCE
- Safety messages
- Hazards
- INTRODUCTION
- Ultimaker 2+ at a glance
- Specifications
- UNPACKING AND INSTALLATION
- Unboxing
- Installation
- OPERATION
- Display and controller
- First use
- Bed leveling
- Loading and changing filament
- Starting a print
- Cura software
- Using glue
- Changing nozzles
- MAINTENANCE
- Glass plate
- The feeder
- Lubricating the axes
- Atomic method
- HELP & SUPPORT
- Troubleshooting
- Support
2 Extended
Table of contents
- Table Of Contents
- WELCOME TO THE ULTIMAKER 2 EXTENDED
- Safety and compliance
- Specifications
- SETTING UP THE ULTIMAKER 2 EXTENDED
- Unboxing
- What's in the box
- Ultimaker 2 Extended at a glance
- Installing accessories
- GETTING STARTED
- Configuration wizard
- First print
- ADVANCED PRINTING OPTIONS
- Cura
- Display and controller
- MAINTENANCE & SUPPORT
- Maintenance
- Troubleshooting
- Support
2 Extended
Table of contents
- Table Of Contents
- ULTIMAKER 2
- Ultimaker 2 at a glance
- Specifications
- GET STARTED
- Unboxing
- Installation
- First use
- THE BASICS
- Changing filament
- Bed leveling
- Cura software
- Using glue
- Display and controller
- MAINTENANCE
- The glass plate
- The feeder
- Lubricating the axes
- Atomic Method
- HELP & SUPPORT
- Troubleshooting
- Support
- Safety and compliance
2 Extended
Table of contents
- Table Of Contents
- Safety and compliance
- Safety messages
- Hazards
- Introduction
- Main components Ultimaker 2 or Ultimaker 2 Extended
- specifications
- Unpack and install the hardware
- Unboxing
- Installing the hardware accessories
- Set up for first use
- Build plate leveling
- Loading material
- Installing Ultimaker Cura
- Operation
- Control and display
- Material
- Preparing a print with Ultimaker Cura
- Starting a print
- Removing the print
- Changing the material and nozzle
- Maintenance
- Update the firmware
- Build plate calibration
- Storage and handling of materials
- Hardware maintenance
- Clean the printer
- Lubricate the axles
- Check for play on axles
- Lubricate the lead screw of the Z motor
- Retighten the hot-end isolator
- Clean the feeder and replace the Bowden tube
- troubleshooting
- Error messages
- Clogged nozzle
- Print quality issues
manualsdatabase
Your AI-powered manual search engine