IBM SureMark 4610 TG8 manuals
SureMark 4610 TG8
Table of contents
- Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- who should read this manual
- where to find more information
- summary of changes
- Part 1. General information
- Updated April
- Chapter 1. Introduction
- Chapter 1. Introduction
- Description of models
- Features used with the SureMark printers
- Comparison of the SureMark models
- Planning information
- Communication interfaces
- models ti8, ti9, tg8, tg
- Power requirements
- Hardware requirements
- application requirements
- Resident code
- Chapter 2. Installation instructions
- Chapter 2. Installation instructions
- Unpacking the printer
- Installing SureMark for USB communication
- Using the wall mounting feature
- Installing the fillers
- Installing fillers for USB printers
- EIA-232 communication mode selections (all models except TI8, TI9, TG8, TG9)
- dtr/dsr control
- EIA-232 communication mode selections (Models TI8, TI9, TG8, TG9)
- USB communication mode
- Chapter 3. SureMark installation, service, and utility software
- Chapter 3. SureMark installation, service, and utility software
- Software adjustments (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, and TG9)
- Using the reference/service diskettes (Models TI1 and TI2)
- fonts and logos utilities
- Using a firmware update diskette (Models TI1 and TI2 only)
- Using POSS for Windows to update SureMark printer firmware (RS-485 and USB only)
- Updating SureMark firmware using temporary EIA-232 attachment
- Limitation on updating firmware
- printing buffer data on thermal/impact printers
- Emulating an Epson single-station printer (single-station only)
- MICR data parser sample code (Models TI2, TI4, TI8, TI9, TG4, TG8, and TG9 only)
- Part 2. Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, TG9
- Chapter 4. Operation
- Ribbon loading
- Paper loading
- Clearing jams in the check flipper area
- MICR reader read head cleaning
- Thermal print head cleaning
- Document scanner cleaning (Model TI8, TI9, TG8, TG9)
- Document scanner calibration (Models TI8, TI9, TG8, TG9)
- Chapter 5. Testing and problem analysis
- Offline tests
- Document insert test
- MICR reader and check flipper test (Models TI2, TI4, TI8, TI9, TG4, TG8, and TG9 only)
- EIA-232 hex dump
- Problem determination
- Part 3. Models TF6 and TM6
- Chapter 6. Operation (Models TF6 and TM6)
- Chapter 7. Testing and problem analysis (Models TF6 and TM6)
- Offline test
- Resetting the printer - offline
- Part 4. Appendixes
- Appendix A. Consumable supplies
- Document insert forms (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8 and TG9 only)
- Print ribbons (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, and TG9 only)
- Appendix B. Printer maintenance procedures
- Appendix C. Technical information
- Memory units
- RS-485 serial I/O parameters
- EIA-232 connector pin assignments
- USB connector pin assignments
- Generic code
- Code page 437
- Code page 858
- Code page 860
- Code page 863
- Code page 865
- Impact printing fonts (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, and TG9)
- Appendix D. EIA-232 programming information
- Appendix D. EIA-232 programming information
- Table Of Contents
- Table Of Contents
- EIA-232 commands summary by function
- Table Of Contents
- Alphabetized EIA-232 commands summary
- System commands
- Status request
- Preset or Onetime-Set commands
- Download graphics (logo) commands
- Predefine messages
- Download user-defined characters
- Thermal code
- Proportional font
- Impact code
- Flash storage write
- Send checksum of flash EPROM sector
- Microcode tolerance (MCT) information - request
- Setup commands
- Set or cancel double-wide mode
- Set or cancel double-high mode
- Set or cancel emphasized printing
- Set or cancel unidirectional printing
- Set print station
- Set code
- Set print station parameters
- Select color printing
- Set sheet eject length
- Set relative position
- Set error recovery function
- Define document wait time
- Select character for reprinted lines
- Enable or disable the feed buttons
- Enable or disable upside-down printing
- Select character size for scalable fonts
- Fix font matrix
- Select thermal paper
- Select horizontal size of bar code
- Select font for HRI
- Print PDF417 bar code using binary mode
- Select aspect ratio PDF417 bar code
- Print character commands
- Print and feed paper in reverse using minimum units
- Print predefined graphics (logo) command
- Miscellaneous commands
- Paper cut/DI eject
- Retrieve size of user flash storage
- Check processing commands (Models TI2, TI4, TI8, TI9, TG4, TG8, and TG9 only)
- MICR read
- Flip check
- Print scanned image
- Store scanned image and/or select partial image for retrieval
- Retrieve scanned image
- Scanner calibration
- Retrieve next image location
- Asynchronous (real-time) commands
- Data buffer management and batch printing
- Hold printing until buffer is released
- Select printable area
- Set relative vertical position
- Set relative horizontal position
- Print and form feed and cut the paper
- Landscape mode
- landscape printing commands
- Status summary
- Status byte 2
- Status byte 5
- Appendix E. Uploading electronic journal data
- Upload the EJ data
- Appendix F. Proportional fonts
- Layout using align commands
- Layout using set tab position
- Appendix G. Emulation support for Epson single-station printer
- Commands with limited support in emulation mode
- Commands not supported in emulation mode
- Appendix H. Safety information
- Appendix I. Notices
- Electronic emission notices
- Industry Canada Class A Emission Compliance statement
- Chinese Class A warning statement
- Taiwanese Class A warning statement
- Product Recycling and disposal
- Battery return program
- For the European Union
- Flat panel displays
- Index
manualsdatabase
Your AI-powered manual search engine