Contents - Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- who should read this manual
- where to find more information
- summary of changes
- Part 1. General information
- Updated April
- Chapter 1. Introduction
- Chapter 1. Introduction
- Description of models
- Features used with the SureMark printers
- Comparison of the SureMark models
- Planning information
- Communication interfaces
- models ti8, ti9, tg8, tg
- Power requirements
- Hardware requirements
- application requirements
- Resident code
- Chapter 2. Installation instructions
- Chapter 2. Installation instructions
- Unpacking the printer
- Installing SureMark for USB communication
- Using the wall mounting feature
- Installing the fillers
- Installing fillers for USB printers
- EIA-232 communication mode selections (all models except TI8, TI9, TG8, TG9)
- dtr/dsr control
- EIA-232 communication mode selections (Models TI8, TI9, TG8, TG9)
- USB communication mode
- Chapter 3. SureMark installation, service, and utility software
- Chapter 3. SureMark installation, service, and utility software
- Software adjustments (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, and TG9)
- Using the reference/service diskettes (Models TI1 and TI2)
- fonts and logos utilities
- Using a firmware update diskette (Models TI1 and TI2 only)
- Using POSS for Windows to update SureMark printer firmware (RS-485 and USB only)
- Updating SureMark firmware using temporary EIA-232 attachment
- Limitation on updating firmware
- printing buffer data on thermal/impact printers
- Emulating an Epson single-station printer (single-station only)
- MICR data parser sample code (Models TI2, TI4, TI8, TI9, TG4, TG8, and TG9 only)
- Part 2. Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, TG9
- Chapter 4. Operation
- Ribbon loading
- Paper loading
- Clearing jams in the check flipper area
- MICR reader read head cleaning
- Thermal print head cleaning
- Document scanner cleaning (Model TI8, TI9, TG8, TG9)
- Document scanner calibration (Models TI8, TI9, TG8, TG9)
- Chapter 5. Testing and problem analysis
- Offline tests
- Document insert test
- MICR reader and check flipper test (Models TI2, TI4, TI8, TI9, TG4, TG8, and TG9 only)
- EIA-232 hex dump
- Problem determination
- Part 3. Models TF6 and TM6
- Chapter 6. Operation (Models TF6 and TM6)
- Chapter 7. Testing and problem analysis (Models TF6 and TM6)
- Offline test
- Resetting the printer - offline
- Part 4. Appendixes
- Appendix A. Consumable supplies
- Document insert forms (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8 and TG9 only)
- Print ribbons (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, and TG9 only)
- Appendix B. Printer maintenance procedures
- Appendix C. Technical information
- Memory units
- RS-485 serial I/O parameters
- EIA-232 connector pin assignments
- USB connector pin assignments
- Generic code
- Code page 437
- Code page 858
- Code page 860
- Code page 863
- Code page 865
- Impact printing fonts (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, and TG9)
- Appendix D. EIA-232 programming information
- Appendix D. EIA-232 programming information
- Table Of Contents
- Table Of Contents
- EIA-232 commands summary by function
- Table Of Contents
- Alphabetized EIA-232 commands summary
- System commands
- Status request
- Preset or Onetime-Set commands
- Download graphics (logo) commands
- Predefine messages
- Download user-defined characters
- Thermal code
- Proportional font
- Impact code
- Flash storage write
- Send checksum of flash EPROM sector
- Microcode tolerance (MCT) information - request
- Setup commands
- Set or cancel double-wide mode
- Set or cancel double-high mode
- Set or cancel emphasized printing
- Set or cancel unidirectional printing
- Set print station
- Set code
- Set print station parameters
- Select color printing
- Set sheet eject length
- Set relative position
- Set error recovery function
- Define document wait time
- Select character for reprinted lines
- Enable or disable the feed buttons
- Enable or disable upside-down printing
- Select character size for scalable fonts
- Fix font matrix
- Select thermal paper
- Select horizontal size of bar code
- Select font for HRI
- Print PDF417 bar code using binary mode
- Select aspect ratio PDF417 bar code
- Print character commands
- Print and feed paper in reverse using minimum units
- Print predefined graphics (logo) command
- Miscellaneous commands
- Paper cut/DI eject
- Retrieve size of user flash storage
- Check processing commands (Models TI2, TI4, TI8, TI9, TG4, TG8, and TG9 only)
- MICR read
- Flip check
- Print scanned image
- Store scanned image and/or select partial image for retrieval
- Retrieve scanned image
- Scanner calibration
- Retrieve next image location
- Asynchronous (real-time) commands
- Data buffer management and batch printing
- Hold printing until buffer is released
- Select printable area
- Set relative vertical position
- Set relative horizontal position
- Print and form feed and cut the paper
- Landscape mode
- landscape printing commands
- Status summary
- Status byte 2
- Status byte 5
- Appendix E. Uploading electronic journal data
- Upload the EJ data
- Appendix F. Proportional fonts
- Layout using align commands
- Layout using set tab position
- Appendix G. Emulation support for Epson single-station printer
- Commands with limited support in emulation mode
- Commands not supported in emulation mode
- Appendix H. Safety information
- Appendix I. Notices
- Electronic emission notices
- Industry Canada Class A Emission Compliance statement
- Chinese Class A warning statement
- Taiwanese Class A warning statement
- Product Recycling and disposal
- Battery return program
- For the European Union
- Flat panel displays
- Index
|
v Font C is 8 dots (wide) × 16 dots (high) with the last 2-dot row used fordescenders.(1.0 mm × 2.0 mm character height including descenders, 1.0 mm × 1.75 mmexcluding descenders)v Font C, starting with level 38 micro code, is 8 dots (wide) and 20 dots (high) withthe last 2-dot row used for descenders.(1.0 mm × 2.5 mm character height including descenders, 1.0 mm × 2.25 mmexcluding descenders)The number of characters printed per inch depends on the character size, theintercharacter spacing, and the chosen font. For example:v 17 cpi ⇒ 10-dot wide character + 2-dot space (font A) ⇒ 48 characters per linev 15 cpi ⇒ 10-dot wide character + 3-dot space (font A) ⇒ 44 characters per linev 12 cpi ⇒ 12-dot wide character + 5-dot space (font B) ⇒ 34 characters per linev 20 cpi ⇒ 8-dot wide character + 2-dot space (font C) ⇒ 57 characters per lineYou can choose the character size of four user-defined character sets (code pages)or two proportional fonts. The parameter ranges for user-defined character sets are:v 8 ≤ dot width ≤ 16v 16 ≤ dot height ≤ 32 (must be a multiple of 2)The parameter ranges for characters in proportional fonts are:v 8 ≤ dot width ≤ 32v 8 ≤ dot height ≤ 32Notes:1. Any of the thermal printing fonts can be scaled up to eight times the definedwidth and eight times the defined height. The scaling factor for the width doesnot have to equal the scaling factor for the height. For example, you couldspecify twice the width and five times the height.2. For paper that has a width of 80 mm, the cash receipt print line is 72 mm (2.83in.) long. There are 576 dots per line and 203 dots per inch.Impact printing fonts (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8,and TG9)The resident character set has a font of 7 half-dots (wide) × 9 dots (high). There areno descenders.v Font A prints 150 half-dots per inch = resident character size is 1.2 mm × 2 mm.v Font B prints 120 half-dots per inch = resident character size is 1.5 mm × 2 mm.The number of characters printed per inch depends on the character size, theintercharacter spacing, and the chosen font. For example:v 17 cpi ⇒ font A with 7 half-dot-wide character + 2 half-dot space ⇒ 52characters per linev 15 cpi ⇒ font A with 7 half-dot-wide character + 3 half-dot space ⇒ 47characters per linev 12 cpi ⇒ font B with 7 half-dot-wide character + 3 half-dot space ⇒ 37characters per lineYou can choose the character size of the two user-defined character sets (codepages) within the following parameters:v 4 ≤ half-dot width ≤ 16v 4 ≤ dot height ≤ 16Updated April 2, 2009Appendix C. Technical information 99
|
