—D C D r i v e sABB industrial drivesDCS880 Quick guide

DCS880 Drive manuals

Ratings, types and voltages

Unpacking and mechanical installation

Type code and plus codes

Brief instructions for virtual CD and documents overview

Notes on EMC

Start, Stop and E-Stop control

Planning the electrical installation, size H1 5

Terminal locations of the converter

Control circuit terminal layout

Notes For North American Installations

DCS880 control panel

Drive composer PC tool

Parameter groups

Safety instructions, drives commisioning

Autotuning warning AF90

Environmental conditions

User macros

Drive logic and main control word

Fieldbus control

Overview control (Drive composer printout)

Declarations

DCS Family

ABB DCS880 Series Quick Manual

DCS880 Drive Manuals

What this chapter contains

Installation and maintenance work

Grounding

Printed circuit boards and fiber optic cables

Operation

Chapter overview

Type code

Plus codes

Main circuit and control

Before installation

Terminal options for converter modules size H1 ... H4

Terminal cover according to VBG 4 regulations

Semiconductor fuses (F1)

Semiconductor fuses (F1) and fuse holders for armature circuit

Auxiliary transformer (T2) for electronic system / fan supply

EMC filters (E1)

Converters size H1 ... H4 configuration using an OnBoard field exciter

Cooling fans

Monitoring the DCS880 power section

Cross-sectional areas - Tightening torques

Selecting the control cables

Connection of a motor temperature sensor to the drive I/O

IT (ungrounded) systems

Location F-type options and interfaces

Pulse encoder connection

Pulse encoder connection principles

Connecting the signal and control cables

Installation checklist

Current ratings - IEC regenerative

Current ratings - IEC non regenerative

Control circuit terminals on the SDCS-CON-H01

XAI: Reference voltages and analog inputs

RO1, RO2, RO3: Relay outputs

XDIO: Digital inputs / outputs

XSMC: Mains contactor

Additional terminals

Ground isolation diagram

Jumpers and switches

Interface board SDCS-PIN-H01

Technical data

Armature circuit interface

Circuit diagram

Fuses and fuse holders IEC

Line reactors IEC

Auxiliary transformer (T2) for converter electronics and fans

Other cables

DCS880 series

Armature converter DCS880 H5

Armature converter DCS880 H6

Armature converter DCS880 H7 and H8

Unpacking and examining the delivery (H1 ... H3)

Unpacking and examining the delivery (H4)

Unpacking and examining the delivery (H5)

Unpacking and examining the delivery (H6)

Unpacking and examining the delivery (H7, H8)

Delivery check

Installing the drive (H1 ... H3)

Installing the drive (H4, H5)

Installing the drive (H6 ... H8)

Mounting the converter module H5 inside an enclosure

Mounting the H7 power unit inside an enclosure

Mounting the H8 power unit inside an enclosure

Fuses (F3.x) and fuse holders for field circuit

Single-phase autotransformer (T3) for field circuit (adapt voltage)

Line reactors for single- and 3-phase connection of field converters

Converters size H5 configuration using FEX-425-Int field exciter

Converters size H6 configuration using a FEX-425-Int field exciter

Converters size H1 ... H6 configuration using external field exciters DCF803, DCF804

Converters size H7 and H8 configuration using external field exciters DCF803, DCF804

Converters size H1 ... H3 as large field exciter

Fan connection for DCS880 (H1 ... H4)

Fan connection for DCS880 (H5 ... H8)

Selecting the power cables

Location F-type adapters and interfaces

FEA-03 I/O extension adapter configuration

DCSLink wiring

Connecting a control unit at H7 and H8 power units

Current ratings - IEC regenerative converters (S02)

Current ratings - IEC non regenerative converters (S01)

Control board SDCS-CON-H01 (H1 ... H8)

Intermediate cover

Replacing the memory unit

DDCS Interface configuration

DDCS branching unit NDBU-95

DCSLink board SDCS-DSL-H1x (H1 ... H8)

Daisy chain DPI-H01 kit (H1 ... H8)

Power Interface board SDCS-PIN-H01 (H1 ... H5)

Power supply board SDCS-POW-H01 (H6 ... H8)

Field circuit interfaces SDCS-BAB-F01 and SDCS-BAB-F02 (H1 ... H4)

Measuring board SDCS-PIN-H51 (H6 ... H8)

Firing pulse transformer board SDCS-PIN-H41 (H6 ... H8)

Optical power link board SDCS-OPL-H01 (H7, H8)

Location of the SDCS-OPL-H01

Connection between firing and control board for H6 ... H8

Galvanic isolation - T90, A92, F11, F90

DC-DC transducer A92 (1)

Transformer T90

Size H8 lefthand (+P906)

Size H8 righthand (+P906)

Branch fuses installed inside converter sizes H5 ... H8

DCF803-0016, FEX-425-Int and DCF803-0035

Electrical data

DCSLink communication

RS232-Port