ACP OMNISTIM 500 PRO User Manual

ACP OMNISTIM 500 PRO User Manual Manual pdf 30 page image

- 26 - OMNISTIM ® 500 PRO USER MANUALCOPYRIGHT © 2004 - 2018, ACCELERATED CARE PLUS CORP., ALL RIGHTS RESERVEDMuscle Re-EducationThe following protocols are found by pressing the MUSCLE RE-ED protocol button. The first protocol displayed isMFAC SURFACE DEEP MUSCLE. Other protocols follow, in the sequence presented below, by continuouslypressing the MUSCLE RE-ED button.A. MFAC SURFACE DEEP MUSCLE:Treatment of muscle disuse atrophy for strength development, targeting superficial and deep muscle groups.Bipolar set-up over agonist and antagonist muscles for target muscle. Intensity should be set to elicit a grade 2-4muscle contraction. Treatment times can be reduced based on muscle fatigue. Joint movement should berestricted by holding manually, or using weights or exercise bands. Activation of muscle with electricalstimulation at a high intensity for a short time with long “ON/OFF” ramps reduces atrophy and improvesstrength. The patient should participate to the extent possible by contracting during the stimulation “ON” time.USER ADJUSTABLEPARAMETER (Y/N)ORDER INPARAMETERSET LOOPPARAMETER NAME ADJUSTABLERANGE (UNIT) DEFAULT (UNIT)Y 9 CARRIER FREQ 2.0, 2.5, 4.0, 5.0, 10.0 (kHz) 2.5 (kHz)Y 6 BURST FREQUENCY 0.0…250 (Hz) 75 (Hz)N BURST RATE SCAN 20 (%)N RATE SCAN ONN RATE SCAN TIME 4 (s)Y 1 TREATMENT TIME 0…99 (min) 10 (min)Y 2 8 2 B OUTPUT DELAY 0.0…9.9 (s) 0.0 (s)Y 4 RAMP UP 0.0…9.9 (s) 2.0 (s)Y 5 RAMP DOWN 0.0…9.9 (s) 2.0 (s)Y 2 T-ON 0…30 (s) 10 (s) 1Y 3 T-OFF 0…199 (s) 50 (s) 1Y 7 Channel Mode A/B SIMULTANEOUS, A/BALTERNATE, B DELAYED A/B SIM.1 When T-OFF = 0, T-ON = CONTINUOUS.2 B OUTPUT DELAY parameter is shown only when the Channel Mode is set to B DELAYED.B. LVPC SURFACE MUSCLE:Treatment of muscle disuse atrophy for strength development, targeting smaller superficial muscle groups.Bipolar set-up over agonist and antagonist muscles for target muscle. Intensity should be set to elicit a grade 2-4muscle contraction. Treatment times can be reduced based on muscle fatigue. Joint movement should berestricted by holding manually, or using weights or exercise bands. Activation of muscle with electricalstimulation at a high intensity for a short time with long “ON/OFF” ramps reduces atrophy and improvesstrength. The patient should participate to the extent possible by contracting during the stimulation “ON” time.USER ADJUSTABLEPARAMETER (Y/N)ORDER INPARAMETERSET LOOPPARAMETER NAME ADJUSTABLERANGE (UNIT) DEFAULT (UNIT)Y 6 PHASE DURATION 40…300 (μs) 70 (μs)Y 7 PULSE RATE 0.0…250 (Hz) 50.0 (Hz)Y 1 TREATMENT TIME 0…99 (min) 10 (min)Y 2 9 2 B OUTPUT DELAY 0.0…9.9 (s) 0.0 (s)Y 4 RAMP UP 0.0…9.9 (s) 2.0 (s)Y 5 RAMP DOWN 0.0…9.9 (s) 2.0 (s)Y 2 T-ON 0…30 (s) 10 (s) 1Y 3 T-OFF 0…199 (s) 50 (s) 1Y 8 Channel Mode A/B SIMULTANEOUS, A/BALTERNATE, B DELAYED A/B SIM.1 When T-OFF = 0, T-ON = CONTINUOUS.2 B OUTPUT DELAY parameter is shown only when the Channel Mode is set to B DELAYED.