ADJ Mega Go Flood Par HO User Instructions

Contents

ADJ Products, LLC - www.adj.com - Mega Go Flood Par HO User Manual Page 11Mega Go Flood Par HO Operating Instructionsas the ADJ Show Designer™.DMX Mode:Operating through a DMX controller gives the user the freedom tocreate their own programs tailored to their own individual needs.This function also allows you to use your fixtures as spot lights.The Mega Go Flood Par HO has 7 DMX modes: 1 Channel mode, 2Channel mode, 3 Channel mode, 4 Channel mode, 5 Channel mode,6 Channel mode, and a 7 Channel mode. See pages 16-20 for eachmodes’ DMX traits.1. This function will allow you to control each individual fixture’straits with a standard DMX 512 controller.2. To run your fixture in DMX mode press the MODE button until“A.XXX” is displayed. “XXX” represents the current displayed ad-dress. Use the UP or DOWN buttons to select your desired DMXaddress, then press the SETUP button to select your DMXChannel mode.3. Use the UP or DOWN buttons to scroll through the DMX Channelmodes. The Channel modes are listed below:To run the 1 Channel Mode, press the MODE button until “Ch.01”is displayed. This is the 1 Channel DMX Mode.To run the 2 Channel Mode, press the MODE button until “Ch.02”is displayed. This is the 2 Channel DMX Mode.To run the 3 Channel Mode, press the MODE button until “Ch.03”is displayed. This is the 3 Channel DMX Mode.To run the 4 Channel Mode, press the MODE button until “Ch.04”is displayed. This is the 4 Channel DMX Mode.To run the 5 Channel Mode, press the MODE button until “Ch.05”is displayed. This is the 5 Channel DMX Mode.To run the 6 Channel Mode, press the MODE button until “Ch.06”is displayed. This is the 6 Channel DMX Mode.To run the 7 Channel Mode, press the MODE button until “Ch.07”is displayed. This is the 7 Channel DMX Mode.4. Please see pages 16-20 for DMX values and traits.5. After you have chosen your desired DMX Channel mode plug inthe fixture via the XLR connections to any standard DMX control-ler.Mega Go Flood Par HO Operating InstructionsOperating Power:There are two ways to supply power to this unit; battery power or ACpower.• AC Power - To run the unit using AC power, plug the unit into a powersource, and put the Load Switch into the ON position. When using ACpower make sure the Battery Switch is in the OFF position.• Battery Power - To run the unit using Battery power, put the Load andBattery Switches in the ON position.LED Display On/Off:To set the LED display to turn off after 20 seconds, press the MODEbutton until “don” is displayed, press the UP button to display “doff”.Now the display will disappear after 20s. Press any button to turnthe display on again. Be advised though that the display will turn offautomatically after 20 seconds.To set the display press the MODE button until “dXX” is displayed.Use the UP or DOWN buttons to select either:“don” = LED display on at all times.“doFF” = LED display shuts off after 20 seconds.LED Display Inversion:Follow these instructions to flip the display 180° so that the displaycan be read upside down.1. Plug the fixture in and press the MODE button until “dXX” is dis-played. “XX” represents either “on” or “oFF”.2. Press the SET UP button until “Stnd” is displayed.3. Press the UP or DOWN buttons to reverse the display 180°.Operating Modes:The Mega Go Flood Par HO has five operating modes:• Sound-Active mode - The unit will react to sound, chasing throughthe built in programs.• Static Color Mode - There are 35 colors to choose from.• Auto Mode - There are 16 Auto Modes to choose from.• RGB Mode - Choose one of the three colors to remain static oradjust the intensity of each color to make your desired color.• DMX control mode - This function will allow you to control eachindividual fixtures traits with a standard DMX 512 controller such asADJ Products, LLC - www.adj.com - Mega Go Flood Par HO User Manual Page 10