ADJ WiFly QA5 IP User Instructions

Also see for WiFly QA5 IP: User instructions

Contents

WiFly QA5 IP ADJ RFC OperationThe ADJ RFC remote (sold seperately) has many different functions andallows you to control your WiFly QA5 IP from long distance. The ADJRFC remote can control your system up to 150 ft. To use the RFC youmust first activate the fixtures receiver, to activate the receiver pleasesee the instructions on page 14.BLACKOUT - Pressing this button will blackout the fixture.AUTO RUN - This button will run an automatic program. There are 3Auto Run programs to choose from. Each press of the button will switchbetween the different modes. You can control the speed of the Auto Runmodes by pressing the SPEED button and then pressing the “+” and “-”buttons.• AFXX = Color Fade mode, there are 16 Color Fade modes to choosefrom. Use the UP or DOWN buttons to scroll through the differentAuto Fade modes.• AJXX = Color Change mode, there are 16 Color Change modes tochoose from. Use the UP or DOWN buttons to scroll through thedifferent Auto Change modes.• A-JF = Both Color Fade and Color Change modes running.PROGRAM SELECTION - Press this button to switch between StaticColor mode and Slave mode. Each press of this button will switch be-tween the two modes. When in Static Color mode, use the “+” or “-” toscroll through the 64 colors. Once you have found your color, you canpress the FLASH button to activate strobing and use the “+” or “-” to ad-just the Flash rate.FLASH - This button will activate the flash (strobe) effect. You can con-trol the flash speed by pressing the “+” and “-” buttons.SPEED - Press this button and use the “+” & “-” buttons to adjust thespeed of the Auto run mode.R G B W/A - Press either one of these buttons and the press the “+” or“-” to adjust the brightness. Press the FLASH button to activate strobingand use the “+” or “-” to adjust the Flash rate.“+” and “-” - Use these buttons to adjust the flash rate, speed of theAuto Run mode, Auto Run program selection, sound sensitivity, andcolor select.ADJ Products, LLC - www.adj.com - WiFly QA5 IP User Manual Page 14ADJ Products, LLC - www.adj.com - WiFly QA5 IP User Manual Page 13WiFly QA5 IP WiFly Set UpWiFly QA5 IP WiFly Master-Slave Set UpWith this feature you are able to control the unit with DMX without the needof XLR cables. Your DMX controller must be connected to a ADJ WiFlyTransCeiver to use this function. You are able to communicate up to 400 feet(open line of sight)NOTE: The ADJ RFC control must be set to OFF to use this function.See pages 10-11 to turn OFF ADJ RFC.1. Turn on the WiFly function using the instructions on page 11.2. Follow the instructions on page 11 to set the Wireless address. Theaddress must match the address set on the WiFly Transceiver.3. After you have set the WiFly address, follow the DMX instructions onpages 9-10 to select your desired DMX Channel mode and set yourDMX address.4. Apply power to the ADJ WiFly Transceiver. The fixture must be set upfirst before you apply power to WiFly Transceiver.Note: If the sync does not work, switch the WiFly power off then on again.This feature will let you link units to run in a master-slave mode without theuse of XLR cables.NOTE: The ADJ RFC control must be set to OFF on all the units to usethis function. See pages 10-11 to turn OFF ADJ RFC.1. Follow the instructions on page 11 to set the Wireless address. Theaddresses on each fixture must be the same.2. After you have set the WiFly address, select your master unit and setyour desired operating mode.3. Turn on the WiFly function using the instructions on page 11.4. For the Slave units, put the unit in Slave mode. See page 15 Master-Slave configuration when setting the unit as a Slave. Then switch ON theWiFly power switch.NOTE: If they do not sync up master-slave, switch the Master fixturesWiFly power switch off then on again.

/ 14

Related manuals for ADJ WiFly QA5 IP