Absolute Process Instruments APD 41391 Quick Start Manual

Absolute Process Instruments APD 41391 Quick Start Manual Manual pdf 1 page image

How to Order—Factory Ranged and Configured OptionsModel Power Input Outputs Alarm Code DescriptionAPD 41391 85-265 VAC, 60-300 VDCSpecifyT/C type,temperaturerange in°F or °CCh. 1specifyVDC or mADCrangeCustomPush-to-Test___% spanCh. 2specifyT/C typenone-BNRAHPHTUUpscale burnout (standard)Downscale burnoutNo burnout, last valid valueReverse-acting alarmLatching relay, power-off resetLatching relay, push button resetConformal coating for moistureresistanceAPD 41391 D 9-30 VDC, 10-32 VACAPD 41391 H 85-265 VAC, 60-300 VDC HI alarm(failsafe)APD 41391 DH 9-30 VDC, 10-32 VACAPD 41391 L 85-265 VAC, 60-300 VDCLO alarmAPD 41391 DL 9-30 VDC, 10-32 VACThermocouple Input to DC & Thermocouple Dual Output Splitter/Converter, Factory Ranged APD 413911 Input: Any Thermocouple2 Outputs: Process Voltage or mA + Any Thermocouple, Alarm Relay OptionsO Split or Convert a T/C to DC Output & Any T/C OutputO Add Additional Isolated Output to Existing T/CO Zero and Span Output CalibrationO Input LoopTracker® LEDO Sink/Source for DC OutputQ Convert/Isolate Thermocouples for PLC Input,Control and/or ValidationQ Interface Thermocouples with Panel Meters, PLCs,Recorders, Data Acq., DCS, & SCADA SystemsApplicationsThermocouple Input, Factory SetT/C types: J, K, T, E, M, N, P, R, S, B, C, D, GTemp. range: Full ANSI range, or specify °F or °C rangeLinearity: ±0.1°C and 0.001°C resolutionLinearization: Polynomial, 1°C segments for types M and PT/C CJC: AutomaticT/C current: Less than 10 μA, including burnout senseT/C burnout: Upscale (standard), B: downscale, N: noneCustom: Provide T/C millivolt data, °F or °C rangeStatus LEDsLoopTracker: Variable brightness green for input levelYellow LED: Output 1 Push-to-Test status, error statusRed/green LED: Alarm state (with alarm option only)DC Output, Channel 1, Factory SetLinearized to temperatureVoltage: 0-1 V to 0-10 V (10 mA max.), ±1 V to ±10 VCurrent: 0-1 mA to 0-20 mA20 V compliance, 1000 Ω at 20 mASinking or sourcing outputLoop power: 20 VDC nom., regulated, 25 mADC<10 mVRMS max. rippleThermocouple Output, Channel 2, Factory SetT/C types: J, K, T, E, M, N, P, R, S, B, C, D, GOutput limited by smallest ANSI T/C rangeLinearization: Polynomials, 1°C segments for types M and PT/C CJC: Automatic, can be factory disabledOutput CalibrationZero and span potentiometers for each output, ±15% rangeOutput Push-to-Test (DC Output 1)Front push button and terminals enables/disables test leveloutput. Set to 75% of output span. Specify custom setting.Output Resolution16 bitOutput Ripple and NoiseLess than ±0.2% of spanOptional Alarm RelaySingle setpoint dual DPST contact sets, factory configured1 Form A (NO) and 1 Form B (NC) contact sets (4 terminals)May be field wired for Form C operation8 A max @ 240 VACresistive loadUse external contactprotection (RC snub-ber) for inductive loadsRed/Green bi-colorLED indicates alarmstatusOne set point, 12turn potentiometer,0-100% of spanOne reset point, 12 turn potentiometer, 0-100% of spanDefault: HI alarm, non-latching, normal acting (failsafe)Relay Test button toggles relay to opposite state or resetsrelay with HT optionAmbient Temperature Range and Stability–10°C to +60°C operating ambientBetter than ±0.02% of span per °C stabilityResponse Time500 milliseconds minimumIsolationFull 4-way galvanic: input, output 1, output 2,power, 1200 VRMS min.600 VACp or 600 VDC common mode protection75 dB minimum common mode rejectionSimultaneous 50 Hz and 60 Hz rejectionHousing and ConnectorsIP 40, requires vertical installation on a 35 mm DINrail inside a panel or enclosure. Allow room forair flow. For use in Pollution Degree 2 Environment.Eight 4-terminal removable connectors,14 AWG max. wire sizePower85-265 VAC, 50/60 Hz or 60-300 VDC, 3 W maximumD versions: 9-30 VDC or 10-32 VAC 50/60 Hz, 3 W maximumDimensions1.78" W x 4.62" H x 4.81" D(45 mm W x 117 mm H x 122 mm D)Quick Link: api-usa.com/tc© 02-20api-usa.com1220 American Way Libertyville, IL 60048Phone: 800-942-0315 Fax: 800-949-7502AABSOLUTEBSOLUTE PPROCESSROCESS IINSTRUMENTSNSTRUMENTSFree FactoryI/O Setup!H H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HMade in USAApplications Linkapi-usa.com/appsPb LeadFreeSink or SourceOutput formADC ChannelOutput Test forDC ChannelUniversal PowerOptional AlarmRelayInputLoopTrackerLEDZero andSpan forEach OutputStatus LEDNote: Temperature range is limited by the smallest ANSIrange of the two T/C types selected.Switching Current (A)Switching Voltage (V)0 3 5 10 30 50 100 300 50085310.50.30.1AC inductive load(cos f = 0.4) AC resistiveloadDC inductive load(L/R = 7 ms)DC resistiveloadRemovable PlugsSee WiringDiagrams onNext Page1 2 3 4 5 6 7 89 10 11 12 13 14 15 1625 26 27 28 29 30 31 3221 22 23 2417 18 19 20DescriptionThe APD 41391 accepts a thermocouple temperature input andprovides one DC process output and one thermocouple output.This makes it useful to match up the available thermocoupletype with an instrument input type, for data recording, or whenisolating the input.The thermocouple input type and temperature range are fac-tory set. The DC output type and range, and the thermocoupleoutput type and range are factory set. The DC output and thethermocouple output correspond to the input temperaturerange specified. Mixed T/C types are limited by the ANSItemperature range. Use appropriate thermocouple extensionwire as needed.The input is sampled, CJC compensated, digitally converted toa linearized temperature signal, and then passed to the outputstages where it is converted to a DC output and a simulatedthermocouple output with CJC compensation. Contact factoryif the CJC compensation is to be disabled.Full 4-way galvanic isolation (input 1, output 1, output 2,power) make this module useful for ground loop elimination,common mode signal rejection, and noise pickup reduction.LoopTrackerAn API exclusive feature includes a green LoopTracker LED thatvaries in intensity with changes in the input signal and a redLoopTracker LED that varies in intensity with changes in thechannel 1 DC output signal. It provides a quick visual pictureof your process at all times and can greatly aid in saving timeduring initial startup and troubleshooting.Output Push-to-TestAn API exclusive feature includes an output test switch to pro-vide a fixed output for the DC output channel (independent ofthe input) when pressed. The output test greatly aids in savingtime during initial startup and/or troubleshooting.The output test level is factory set to approximately 75% ofspan but a custom test level may be ordered.

/ 2

Related manuals for Absolute Process Instruments APD 41391