Absolute Process Instruments APD 41393 Quick Start Manual

Absolute Process Instruments APD 41393 Quick Start Manual Manual pdf 1 page image

How to Order—Factory Ranged and Configured OptionsModel Power Input Outputs Alarm Code DescriptionAPD 41393 85-265 VAC, 60-300 VDCSpecifyT/C type,temperaturerange in°F or °CCh. 1 specifyVDC or mADCrangeCustomPush-to-Test___% spanCh. 2 specifyVDC or mADCrangeCustomPush-to-Test___% spannone-BNRAHPHTUUpscale burnout (standard)Downscale burnoutNo burnout, last valid valueReverse-acting alarmLatching relay, power-off resetLatching relay, push button resetConformal coating for moistureresistanceAPD 41393 D 9-30 VDC, 10-32 VACAPD 41393 H 85-265 VAC, 60-300 VDC HI alarm(failsafe std.)APD 41393 DH 9-30 VDC, 10-32 VACAPD 41393 L 85-265 VAC, 60-300 VDC LO alarm(failsafe std.)APD 41393 DL 9-30 VDC, 10-32 VACThermocouple Input to Dual DC Output Splitter/Converter, Factory Ranged APD 413931 Input: Any Thermocouple2 Outputs: Two Independent Process Voltage or mA Signals, Alarm Relay OptionsO Split or Convert a T/C Into 2 Independent DC OutputsO Add Additional Isolated Output to Existing T/CO Zero and Span Output CalibrationO Input LoopTracker® LEDO Sink/Source for DC OutputsQ Split/Isolate T/Cs for PLC Input, Control or ValidationQ Interface Thermocouples with Panel Meters, PLCs,Recorders, Data Acq., DCS, & SCADA SystemsApplicationsThermocouple Input, Factory SetT/C types: J, K, T, E, M, N, P, R, S, B, C, D, GTemp. range: Full ANSI range, or specify °F or °C rangeLinearity: ±0.1°C and 0.001°C resolutionLinearization: Polynomials, 1°C segments for types M and PT/C CJC: AutomaticT/C current: Less than 10 μA, including burnout senseT/C burnout: Upscale (standard), B: downscale, N: noneCustom: Provide T/C millivolt data, °F or °C rangeStatus LEDsLoopTracker: Variable brightness green for input levelYellow LED: Output Push-to-Test status, error statusRed/green LED: Alarm state (with alarm option only)DC Output, Channel 1, Factory SetLinearized to temperatureVoltage: 0-1 V to 0-10 V (10 mA max.), ±1 V to ±10 VCurrent: 0-1 mA to 0-20 mA20 V compliance, 1000 Ω at 20 mASinking or sourcing outputLoop power: 20 VDC nom., regulated, 25 mADC<10 mVRMS max. rippleDC Output, Channel 2, Factory SetLinearized to temperatureVoltage: 0-1 V to 0-10 V (10 mA max.), ±1 V to ±10 VCurrent: 0-1 mA to 0-20 mA20 V compliance, 1000 Ω at 20 mASinking or sourcing outputLoop power: 20 VDC nom., regulated, 25 mADC<10 mVRMS max. rippleOutput CalibrationZero and span potentiometers for each output, ±15% rangeOutput Push-to-Test (Output 1 & Output 2)Front push buttons and terminals enable/disable test level out-puts. Each set to 75% of output span. Specify custom setting.Output Resolution16 bitOutput Ripple and NoiseLess than ±0.2% of spanOptional Alarm RelaySingle setpoint dual DPST contact sets, factory configured1 Form A (NO) and 1 Form B (NC) contact sets (4 terminals)May be field wired for Form C operation8 A max @ 240 VACresistive loadUse external contactprotection (RC snub-ber) for inductive loadsRed/Green bi-colorLED indicates alarmstatusOne set point, 12turn potentiometer,0-100% of spanOne reset point, 12 turn potentiometer, 0-100% of spanDefault: HI alarm, non-latching, normal acting (failsafe)Relay Test button toggles relay to opposite state or resetsrelay with HT optionAmbient Temperature Range and Stability–10°C to +60°C operating ambientBetter than ±0.02% of span per °C stabilityResponse Time500 milliseconds minimumIsolation© 02-20api-usa.com1220 American Way Libertyville, IL 60048Phone: 800-942-0315 Fax: 800-949-7502AABSOLUTEBSOLUTE PPROCESSROCESS IINSTRUMENTSNSTRUMENTSRemovable Plugs1 2 3 4 5 6 7 89 10 11 12 13 14 15 1625 26 27 28 29 30 31 3217 18 19 20 21 22 23 24See WiringDiagrams onNext PageQuick Link: api-usa.com/tcFull 4-way galvanic: input, output 1, output 2,power, 1200 VRMS min.600 VACp or 600 VDC common mode protection75 dB minimum common mode rejectionSimultaneous 50 Hz and 60 Hz rejectionHousing and ConnectorsIP 40, requires vertical installation on a 35 mm DINrail inside a panel or enclosure. Allow room forair flow. For use in Pollution Degree 2 Environment.Eight 4-terminal removable connectors,14 AWG max. wire sizePower85-265 VAC, 50/60 Hz or 60-300 VDC, 3 W maximumD versions: 9-30 VDC or 10-32 VAC 50/60 Hz, 3 W maximumDimensions1.78" W x 4.62" H x 4.81" D(45 mm W x 117 mm H x 122 mm D)Switching Current (A)Switching Voltage (V)0 3 5 10 30 50 100 300 50085310.50.30.1AC inductive load(cos f = 0.4) AC resistiveloadDC inductive load(L/R = 7 ms)DC resistiveloadFree FactoryI/O Setup!H H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HH H H H HH H H H H HMade in USAApplications Linkapi-usa.com/appsPb LeadFreeSink or SourceOutput formADC ChannelsOutput Test forDC ChannelsUniversal PowerOptional AlarmRelayInputLoopTrackerLEDZero andSpan forEach OutputStatus LEDDescriptionThe APD 41393 accepts a thermocouple temperature input andprovides two independent DC process outputs. This makes ituseful to split, isolate, and transmit a thermocouple signal formeasurement, data recording, or validation.The thermocouple input type and temperature range are fac-tory set. The two DC output types and ranges are factory set.The DC outputs can be different and both correspond to theinput temperature range specified. Use appropriate thermo-couple extension wire for the input as needed.The input is sampled, CJC compensated, digitally converted toa linearized temperature signal, and then passed to the outputstages where it is converted to the two DC outputs.Output Sink/Source VersatilityThe APD 41393 includes a 20 VDC loop excitation supply forany channel ordered with a mA output. A mA output can beselectively wired for sinking or sourcing allowing use with apowered or unpowered milliamp device.Full 4-way galvanic isolation (input, output 1, output 2, power)make this module useful for ground loop elimination, commonmode signal rejection, and noise pickup reduction.LoopTrackersAn API exclusive feature includes a green LoopTracker LEDthat varies in intensity with changes in the input signal andred LoopTracker LEDs that vary in intensity with changes inthe DC output signals. It provides a quick visual picture of yourprocess at all times and can greatly aid in saving time duringinitial startup and troubleshooting.Output Push-to-TestAn API exclusive feature includes output test switches for eachDC output to provide a fixed output (independent of the input)when pressed. The output test greatly aids in saving time dur-ing initial startup and/or troubleshooting.The output test level is factory set to approximately 75% ofspan but a custom test level may be ordered.

/ 2

Related manuals for Absolute Process Instruments APD 41393