Accles & Shelvoke CASH Cowpuncher .22R Original Instruction Manual
                                | |
Contents
| 
REPLACING FIRING PIN - item 2 in spare parts list and diagramRemoving the Firing Pin1 Remove the cap from the barrel of the tool2 Prise the bottom Red ‘O’ Ring (Item 5 in spare parts list and diagram) fromthe cap, then repeat the process with the remaining ‘O’ Ring (Once the Red ‘O’ Rings have been removed, we recommend you replace the ‘O’ Rings)3 Remove the three Claws (Item 3 in spare parts list and diagram) from the cap4 Place only the flats of the firing pin into the jaws of a vice and secure5 Place a sturdy, flat metal bar into the slots (Fig 10.01) where the clawswould usually be found and turn the cap using the metal until the firingpin is looseReplacing the Firing Pin1 Replace the firing pin and tighten until it is finger tight2 Place only the flats of the firing pin into the soft jaws of a vice and fasten securelyusing a sturdy, flat metal bar as shown in Fig, 10.01REPLACING PHOSPHOR BRONZE BALLS - item 4 in spare parts list and diagramRemoving the Phosphor Bronze Balls1 Remove the cap from the barrel of the tool2 Prise the bottom Red ‘O’ Ring (Item 5 in spare parts list and diagram) from the cap, then repeat the process withthe remaining ‘O’ Ring (Once the Red ‘O’ Rings have been removed, we recommend you replace the ‘O’ Rings)3 Remove the three claws (Item 3 in spare parts list and diagram) from the cap exposing the Phosphor Bronze Balls4 Remove the Phosphor Bronze Balls from the capReplacing the Phosphor Bronze Balls1 Put a small amount of grease on the area where the ball sits in the cap2 Put the Phosphor Bronze Balls into the greased area3 If not worn, place the claws back into slots on the cap (Replace if worn)4 Put two new ‘O’ Rings over the Phosphor Bronze Balls and the Claws to secure in placeONLY EVER USE GENUINE ACCLES & SHELVOKE REPLACEMENT PARTS. NOT USINGGENUINE PARTS MAY LEAD TO PREMATURE COMPONENT AND TOOL FAILURE, WHICHCOULD ENDANGER THE OPERATOR AND THOSE IN THE IMMEDIATE VICINITY. IT WILLALSO INVALIDATE OUR ORIGINAL EQUIPMENT WARRANTY.ACCLES & SHELVOKE WILL ACCEPT NO LIABILITY IF ANY COMPONENTS OTHER THANTHOSE SUPPLIED BY ACCLES & SHELVOKE ARE USED WITH OUR ORIGINAL EQUIPMENT.THE RESULTANT LIABILITY WILL BE WITH THE END USER OR THE DISTRIBUTOR WHOSUPPLIED THE UNAPPROVED REPLACEMENT PARTS.Accles & Shelvoke provide a comprehensive service and repair facility where customers can have their CASH stunnerserviced by our highly experienced and trained engineers. This service is generally open to UK customers. Overseascustomers are advised to contact their local distributor.4 A quotation will be provided on inspection of the return of the tool, itemising service charges and replacement parts required.4 The service involves the tool being stripped, cleaned and reassembled with the replacement parts quoted to return thetool back to good working order.Customers are advised to contact Accles & Shelvoke direct on +44(0)121 313 3564 to make arrangements to return thetool for service and repair.CASH®CowpuncherSERVICINGP29SECTION 10©Fig. 10.01©2016 Accles & ShelvokeDO NOT ATTEMPT TO USE THIS STUNNING TOOL UNTIL YOU HAVE READ ANDUNDERSTOOD THESE INSTRUCTIONS.ALWAYS WEAR THE CORRECT PERSONAL PROTECTIVE EQUIPMENT (PPE) WHENEVER YOUARE WORKING WITH, CLEANING OR MAINTAINING YOUR COWPUNCHER TOOL. ALWAYSWEAR PROTECTIVE GLASSES AND HEARING PROTECTION. THE CORRECT FOOT PROTECTIONMUST BE WORN. THERE IS A RISK THAT IF THE TOOL IS DROPPED, THE BOLT MAYPENETRATE THE FOOT OF THE TOOL USER.ONLY PERSONNEL WHO HAVE BEEN AUTHORISED TO DO SO SHOULD CONDUCT ANYRECTIFICATION INDENTIFIED IN THIS SECTIONALWAYS POINT THE TOOL AWAY FROM YOUR BODY AND AWAY FROM ANY OTHERPERSON IN THE VICINITY WHEN HANDLING OR OPERATING THE TOOL |
manualsdatabase
Your AI-powered manual search engine