Ace 3108651 User Manual
  | |
Contents | 
© 2003 595-5751-023. TestingCaution: Always turn the circuit breaker off when wiringthe fixture.1. Remove the existing fixture.2. The plastic hanger can be used to hold the fixture while wiring.The small end of the plastic hanger can be threaded through thehole in the center of the cover plate. The small end then goes intoone of the slots on the mounting strap.3. Connect the light control as shown in Figure 1:• Black sensor wire to the black (HOT) house wire.• White sensor wire to the white (NEUTRAL) house wire.2. AimingFigure 2 - Coverage Angles180°8 Ft.70 Ft.Figure 1 - Wiring at Junction Box Plate4. Attach the fixture to the mounting strap with the center mounting bolt.Use a weatherproof sealant to seal the fixture to the junction box.5. Install the protective lamp shields on the lamp holders by liningup the groves on the narrow end of the shields with the dimplesin the lamp holders, push the shields into the lamp holders andturn clockwise slightly.6. Install the lamps in the lamp holders. Do not over tighten.7. Adjustment lamp holders. The lamps should be at least 1 inchaway from the sensor.Caution: Do not mount the sensor above or touching the lamps(keep 1 inch or more from the lamps). The sensor bottom must befacing down for best coverage and to avoid water damage andelectrical shock.Motion SensingLight®From HouseWhite to whiteBlack to blackHouse ground wire to greenground screw on fixture.Push the rubberplug firmly intoplaceSpecifications:Total Lighting Wattage ...................... Up to 300 Watts MaximumLamp Holder Wattage ............... Up to 150 Watts Maximum eachRange ............................................................................ up to 70 ft.Time Delay ...................................................... 1, 5, or 10 minutesCaution: This product is to be used with a U.L. listed rain tight orwet location suitable outlet box. Depending on the installation,additional hardware may be required.This light control automatically turns on lights when motion isdetected.Two lamp holders are provided. The lamp holders are rated at 150watts max. each.Note: Installation of this light control should be done only by thosewith experience in 120 Volt household wiring. Some local codesmay require that a licensed electrician install the light control.Models 3108677/3108651/31086691. InstallationAs an ENERGY STAR® Partner, Heath ® /Zenith hasdetermined that this product meets the ENERGYSTAR® guidelines for energy efficiency. This productis ENERGY STAR® compliant when used with 120Watt bulbs.Note: For under-eave installation, rotate the sensor head 180° bybending the sensor towards the clamp bracket. Rotate the sensorbottom clockwise away from the bracket.The coverage area for the sensor is shown in Figure 2. The sensorshould be aimed so that the motion to be detected is in front of andacross the coverage area. The sensor should be aimed looking out ata horizontal angle. To reduce false triggering, point the sensor awayfrom traffic areas, air conditioners, dryer vents, water pools, oranything which may move or change temperature rapidly.For motion sensing, put the ON-TIME switch on the bottom of thesensor in the 1, 5 or 10 minute position. When motion is detected, thelights will come on the selected time. Note: The photocell keeps thelights from turning on in daylight.To keep lights on all night, flip the light switch off for 1 second thenback on. Turning the light switch off for 1 second then back on willreturn the control to the motion sensing mode. At dawn, the controlwill return to the motion sensing mode and shut off.4. OperationTurn the power back on at the circuit breaker. Turn the light switchon.Note: When first turned on wait about 1 1 /2 minutes for the circuitryto calibrate.Put the TIME switch on the bottom of the sensor in the TEST position.You can now walk in front of the unit and the lights will come on forabout 5 seconds. The TEST mode works both day and night.Walk through the coverage area and point the sensor to obtain thedesired coverage area. Adjust sensitivity as needed. |
Related manuals for Ace 3108651
manualsdatabase
Your AI-powered manual search engine