Banner Sure Cross Performance GatewayPro DX80P*A6 series Instruction Manual

Also see for Sure Cross Performance DX83A: Network manual

Contents

Banner Sure Cross Performance GatewayPro DX80P*A6 series Instruction Manual Manual pdf 28 page image

5 Advanced Setup Instructions and AdditionalInformationRefer to the following sections for advanced setup instructions or additional information on Banner's SureCross wirelesstechnology and its uses.5.1 DX80 Menu StructureThe Gateways and Nodes each have their own menu structure and options.5.1 DX80 Gateway Set-up MenuWhen power is applied, the DX80 begins running. The display screen auto loops through the RUN menu andcommunication begins between the Gateway and Node(s). Auto looping through the RUN menu is the normal operatingmode for all devices on the wireless network.From the RUN Menu (or any menu), single-click button 1 to advance through the top-level menus. The device auto displayloops through the menu options if either of the RUN, DINFO, or FCTRY menus are selected. If the device is paused on theSITE, DVCFG, or DERR menu options, the display does not auto loop.To enter manual scrolling mode, double-click button 2 at the top level menu. Use the instructions shown in the chart belowto navigate the menu system. To return to the top level menus and auto display loop mode, double-click button 2 twice.The * before the menu name indicates a top-level menu option. The () indicate submenu items.When using Rotary Dial Addressing Mode, use the left rotary dial to set the Network ID (NID). Once changed, allow fiveseconds for the devices to update to the new Network ID.NOD XXM XXR XXY XXG XX*DINFO *FCTRY *SITE *DVCFG *DERR*RUNAUTODISPLAYLOOPAUTODISPLAYLOOPAUTODISPLAYLOOP(DEV)GATEWY(NID)XX(SLID)XX(BAUD)XX(PRTY)XX(DEV)GATEWY(RADIOMICRO)V 00.0 A(LCDMICRO)V 00.0 A(DX80S/N)(0000)(DX80MODEL)(0000-00)(PRODDATE)(00-00)Single-clickButton 2 Single-clickButton 2Single-clickButton 2Double-clickButton 2adjust right rotaryswitch to survey theselected NodeSingle-clickButton 2Double-clickButton 2Double-click Button 2NOD XXEC XX CLEARERRERASEDERRDISABL*ERRORDISABL IGNORENextDeviceSingle-click Button 1 to advance through menuAUTODISPLAYLOOPSingle-clickButton 2 Single-clickButton 2Single-clickButton 2 Single-clickButton 2Single-clickButton 2Single-clickButton 2New ErrorDetectedadjust the rotaryswitches to surveythe selected Node(DEV)I/O XXGATEWYNID XXON/OFF(DEV)I/O XXGATEWYNID XXON/OFFEvenNoneOddSingle-clickButton 2Single-clickButton 2SAVESDISPLAYEDVALUESingle-click B119200960038400Single-clickButton 2Single-clickButton 2SAVESDISPLAYEDVALUENEW XXSingle-clickButton 2Single-clickButton 2adjust rotary switchesto set the network IDSAVES NEWVALUESCUR XXSingle-clickButton 2Single-clickButton 2adjust rotary switchesto set slave ID, usingbutton 1 to select thedigitsSAVES NEWVALUES(NID) (SLID) (BAUD) (PRTY)Network ID Slave ID Baud Rate ParitySingle-click B1NEW XXSingle-clickButton 1 Single-clickButton 1Single-clickButton 1 Single-clickButton 1Single-click Button 1 to advance through menu(NAME)XXXXXXXXXXXXSingle-click Button 1 to advance through menuCUR XXDouble-click Button 2Double-clickButton 2* Set to 000000 to use the serial number.Device Info Factory Info Site Survey Device Config Device Error16832Single-clickButton 2Single-clickButton 2SAVESDISPLAYEDVALUESingle-click B1(MAXN)Timing48MANUALAUTOAUTOSETSingle-clickButton 2Single-clickButton 2Single-click B1(XADR)Extended AddressingXADRADJUST ROTARYSWITCH TOSET XADRSingle-clickButton 2XXXXXXSingle-click B1Single-clickButton 2CONFRMXADRXXXXXNETWRKSingle-clickButton 2BINDNGSingle-clickButton 1 or 2RebootSAVED*XXXXXXSure Cross® Performance DX80 Wireless I/O Networks28 www.bannerengineering.com - Tel: 763.544.3164