Banner WORLD-BEAM QS18 Expert Series Instruction Manual

Banner WORLD-BEAM QS18 Expert Series Instruction Manual Manual pdf 19 page image

7 Specifications7.1 Self-Contained Models: SpecificationsSupply Voltage and Current10 V dc to 30 V dc (10% maximum ripple within specified limits) at 30mASupply Protection CircuitryProtected against reverse polarity and transient overvoltagesOutput Protection CircuitryProtected against false pulse on power-up and continuous overload orshort-circuit of outputOutput ConfigurationChannel 1: IO-Link, Push/pull output, configurable PNP or NPN outputChannel 2: Multi-function remote input/output, configurable PNP orNPNOutput Response TimeMomentary delay on power-up, < 0.5 s, output does not conduct duringthis time350 microseconds ON & OFF for high speed response time1 millisecond ON & OFF for standard response time2 millisecond ON & 1 millisecond OFF for robust response timeRepeatability140 microseconds for high speed175 microseconds for standard and robustIO-Link InterfaceSupports Smart Sensor Profile: YesBaud Rate: 38400 bpsProcess Data Widths: 32 bits In, 8 bits OutIODD Files: Provides all programming options of push button andremote input wire, plus additional functionality. See the IO-Link DataReference Guide for more details.Emitter LEDDV, CV, FP, and LP: Visible red, 625 nmD models: Infrared, 940 nmIndicatorsTwo LEDs (1 green, 1 amber)Green On: Indicates power applied and sensor readyGreen Flashing: Indicates sensor operating in marginal state, in need ofreconfigurationAmber On: Indicates output conductingFactory Default SettingsSetting Factory DefaultTEACH/SET D, DV, CV, and FP Models: Two-point StaticTEACHLP Models: Light SETOutput Logic D, DV, CV, and FP Models: Light OperateLP Models: Dark OperateOutput Response Time StandardOffset Percentage 30%Push Button UnlockedAuto Compensation EnabledOFF Delay DisabledPin 4 Output IO-Link Enabled Detection Output (Push-pull)Pin 2 Output Detection Output: High-speed output when usingIO-Link on Pin 4Required Overcurrent ProtectionWARNING: Electrical connections must bemade by qualified personnel in accordancewith local and national electrical codes andregulations.Overcurrent protection is required to be provided by end productapplication per the supplied table.Overcurrent protection may be provided with external fusing or viaCurrent Limiting, Class 2 Power Supply.Supply wiring leads < 24 AWG shall not be spliced.For additional product support, go towww.bannerengineering.com.Supply Wiring (AWG) Required Overcurrent Protection (Amps)20 5.022 3.024 2.026 1.028 0.830 0.5ConstructionHousing: ABSWindow: PMMAMounting TorqueNose Mount: 18 mm mounting nut, 20 Ibf·in (2.3 N·m)Side Mount: Two M3 screws, 5 Ibf·in (0.6 N·m)ConnectionsPVC-jacketed 4-conductor 2 m (6.5 ft) or 9 m (30 ft) unterminated cable,or 4-pin M12/Euro-style or 4-pin M8/Pico-style quick-disconnect, eitherintegral or 150 mm (6 in) cable, are available.Models with a quick disconnect require a mating cordsetOperating Conditions–40 °C to +70 °C (–40 °F to +158 °F)95% at +50 °C maximum relative humidity (non-condensing)Environmental RatingIEC IP67Application NotesIf the push button does not appear to be responsive, perform the pushbutton enable procedureCertificationsWORLD-BEAM QS18 Expert with IO-Linkwww.bannerengineering.com - Tel: + 1 888 373 6767 19