Beamz BAC406 Instruction Manual

2ENGLISHCongratulations to the purchase of this Beamz fixture. Please read this manual thoroughly prior to using the unit in order tobenefit fully from all features.Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions toavoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock.Keep the manual for future reference.- Prior to using the unit, please ask advice from aspecialist. When the unit is switched on for the first time,some smell may occur. This is normal and will disappearafter a while.- The unit contains voltage carrying parts. Therefore doNOT open the housing.- Do not place metal objects or pour liquids into the unitThis may cause electrical shock and malfunction.- Do not place the unit near heat sources such asradiators, etc. Do not place the unit on a vibratingsurface. Do not cover the ventilation holes.- The unit is not suitable for continuous use.- Be careful with the mains lead and do not damage it. Afaulty or damaged mains lead can cause electrical shockand malfunction.- When unplugging the unit from a mains outlet, alwayspull the plug, never the lead.- Do not plug or unplug the unit with wet hands.- If the plug and/or the mains lead are damaged, theyneed to be replaced by a qualified technician.- If the unit is damaged to such an extent that internalparts are visible, do NOT plug the unit into a mains outletand DO NOT switch the unit on. Contact your dealer. DoNOT connect the unit to a rheostat or dimmer.- To avoid fire and shock hazard, do not expose the unit torain and moisture.- All repairs should be carried out by a qualified technicianonly.- Connect the unit to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.- During a thunderstorm or if the unit will not be used for alonger period of time, unplug it from the mains. The ruleis: Unplug it from the mains when not in use.- If the unit has not been used for a longer period of time,condensation may occur. Let the unit reach roomtemperature before you switch it on. Never use the unit inhumid rooms or outdoors.- During operation, the housing becomes very hot. Do nottouch it during operation and immediately after.- To prevent accidents in companies, you must follow theapplicable guide lines and follow the instructions.- Secure the unit with an extra safety chain if the unit isceiling mount. Use a truss system with clamps. Makesure nobody stands in the mounting area. Mount theeffect at least 50cm away from inflammable material andleave at least 1 meter space on every side to ensuresufficient cooling.- This unit contains high intensity LEDs. Do not look intothe LED light to prevent damage to your eyes.- Do not repeatedly switch the fixture on and off. Thisshortens the life time.- Keep the unit out of the reach of children. Do not leavethe unit unattended.- Do not use cleaning sprays to clean switches. Theresidues of these sprays cause deposits of dust andgrease. In case of malfunction, always seek advice froma specialist.- Only operate the unit with clean hands.- Do not force the controls.- If the unit has fallen, always have it checked by aqualified technician before you switch the unit on again.- Do not use chemicals to clean the unit. They damage thevarnish. Only clean the unit with a dry cloth.- Keep away from electronic equipment that may causeinterference.- Only use original spares for repairs, otherwise seriousdamage and/or dangerous radiation may occur.- Switch the unit off prior to unplugging it from the mainsand/or other equipment. Unplug all leads and cablesprior to moving the unit.- Make sure that the mains lead cannot be damaged whenpeople walk on it. Check the mains lead before every usefor damages and faults!- The mains voltage is 220-240Vac/50Hz. Check if poweroutlet match. If you travel, make sure that the mainsvoltage of the country is suitable for this unit.- Keep the original packing material so that you cantransport the unit in safe conditionsThis mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficientmagnitude to cause a shock hazard.This mark attracts the attention of the user to important instructions that are contained in the manual and that he shouldread and adhere to.DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacksshould be aware of the effects that this light effect may have on them.The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate andtheir guarantee!NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and35°C/95°F.Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or yourdealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other.Specifications can be changed without prior notice.