Camp Chef SmokePro PG24DLX Warning & Instruction Booklet

Fig. 11. Do NOT leave this appliance unattended while in use. The usermust remain in the immediate area of the product and have aclear view of the product at all times during operation.2. Keep children and pets away from burner at all times.3. The use of alcohol, prescription or non-prescription drugs mayimpair your ability to properly assemble or safely operatethis appliance.4. For OUTDOOR use only. Do NOT use in a building, garage or anyother enclosed area. Do NOT use in or on recreational vehiclesor boats. NEVER use this appliance as a heater.5. Do not operate appliance under ANY overhead construction.Keep a minimum clearance of 10 feet (3 m) from the sides,front and back of appliance to ANY construction. Keep thearea clear of all combustible material and flammable liquids,including wood, dry plants and grass, brush, paper, andcanvas.6. This product is not intended for commercial use.7. Always allow the appliance to cool before covering with thepatio cover.8. Always cover the appliance, with patio cover (if supplied),when not in use.9. Always unplug grill before installing patio cover.10. Use only on level surface.11. Make sure burner clean-out is closed before starting the grill.12. Make sure the grease bucket is in place before startingthe grill.13. In the event of a fire the dial should be turned to shutdown,close the lid, and leave it closed until the fire goes out. Afterallowing the grill to cool, follow the cleaning instructionsbefore the next use.14. Use only food grade hardwood pellets manufactured for use inpellet grills. Using softwood or heating pellets will void yourwarranty.15. Do not allow the hopper to run out of pellets. Pellets canbe added at any time. The hopper will hold approximately15 pounds of pellets. The pellet usage will vary greatlydepending on the ambient temperature as well ascooking temperature.16. It is recommended that you not store pellets in the hopper forextended periods as they may absorb moisture from the airand clog the auger.17. Keep the lid closed during cooking. The grill is designedto cook with the lid closed.18. Note that the cooking temperature displayed on the digitalreadout is measured near the cooking surface on the leftside of the grill. The actual temperature inside the cookingchamber will vary slightly throughout.19. Do not use accessories not specified for use with appliance.20. Never use gasoline, gasoline-type lantern fuel, kerosene,charcoal lighter fluid, or similar liquids to start or freshen up afire in this appliance. Keep all such liquids well away from theappliance when in use.21. Ashes should be placed in a metal container with a tightfitting lid. The closed container of ashes should be placed ona non combustible floor or on the ground, well away from allcombustible materials, pending final disposal. When the ashesare disposed by burial in soil or otherwise locally dispersed theyshould be retained in the closed container until all cinders havethoroughly cooled.DANGERDo not work on this grill if it is plugged in. Electric shock mayoccur resulting in death or serious injury.ASSEMBLY INSTRUCTIONSATTACH THE LEGS1. Lay the grill on its back.2. Install each of the 4 legs as shown in Fig 1. Make sure the legswith wheels are attached to the right side of the grill with thewheels facing out.3. Stand the grill upright4. Tighten all hardware.ATTACH CHIMNEY AND CHIMNEY CAP1. Install chimney to grill as shown in Fig 2. Make sure to installthe gasket between the grill and the chimney.2. Tighten all hardware.3. Install M6 x 76 Bolt through chimney cap and secure using Qty(1) M6 nut. Thread second nut onto bolt leaving approximately1.5” to the top of the cap. Thread cap assembly down into thechimney bracket until the lower nut hits the bracket. See Fig 2.4. The height of the chimney cap can be adjusted for summer andwinter. In the summer the gap should be approximately 1-1/2”.In the winter the gap should be approximately ½”.5. Tighten all hardware.M8 X 45 BOLTM8 FLAT WASHERM8 LOCK WASHERM8 NUTM6 X 15 SCREWCHIMNEY GASKETM6 NUTM6 X 76 BOLTPARTS LIST1014 PG24-31 PARTSPG24-20 (1)BURNERPG24-21 (1)HEATING RODPG24-22 (1)AUGERPG24-23 (1)AUGER BUSHINGPG24-24 (1)AUGER MOTOR WITH IMPELLERPG24-25 (1)AUGER PIN W/NUTPG24-26 (1)BLOWER MOTOR WITH IMPELLERPG24-27 (1)BLOWER IMPELLERPG24-28 (1)MEAT PROBEM4.2 X 10 SCREW (4)PG24-43 (1)CONTROLLERPG24-30 (1)CONTROLLER KNOBM4.2 X 10 SCREW (2)PG24-50 (1)HOPPER COVERPG24-32 (BLACK) (1)PG24-38 (STAINLESS) OPTIONALHOPPER LIDPG24-33 (1)LID RODM4.2 X 10 SCREW (4)PG24-45 (1)CONTROLLER GASKETPG24-46 (1)GUARD PLATEPG24-49 (1)AUGER IMPELLERPG24-48 (1)POWER CORDPG24-52 (1)HOPPER RAKEPGC24-13 (1)HOPPER CLEANOUTM6 X 15 BOLT (2)PG24-9 (1)PULLOUT KNOBPG24-42 (1)PULLOUT LOCKM6 NUT (2)PG24-53 (1)AUGER GUARDPG24-35 (1)AUGER FAN BOX ASM