Canon DR40-C-VB Installation Manual
Installing the CameraThe procedures for mounting the camera to the ceiling using the indoor dome housing aredescribed below.Before installing the camera, set the IP address and other network information on the camerausing the "VB Initial Setting Tool".For details on how to operate the "VB Initial Setting Tool", see VB-M40 Operation Guide.If using an SD memory card, insert the SD memory card into the camera before installing (see"Using an SD Memory Card" in VB-M40 Installation Guide).ImportantOnce the camera is installed to the ceiling, to insert and remove the SD memory card, the camera mustbe removed from the ceiling and the ceiling bracket dismounted.1 Determine an installation position for the camera and drill holes in the ceilingUsing the bundled template, line up the directon of the camera, determine the locations of thebackside ceiling bracket mounting holes (three) and the ceiling bracket holes, then drill theholes into the ceiling.ImportantWhen mounting the indoor dome housing, be sure no shavings enter the dome.2 Mount the camera to the ceiling bracketAffix with four bundled fixing screw (M3).3 Mount the dust cover to the ceiling bracketAffix with three bundled fixing screw (M3).4 Attach the backside ceiling brackets inside the ceilingFrom the inside of the ceiling, insert the protrusions on the backside ceiling brackets throughthe mounting holes drilled in step 1.5 Temporarily tighten screws to the backside ceiling bracketTemporarily tighten the three bundled ceiling bracket screws (M4) through the ceiling.6 Secure the safety wireSecurely attach the safety wire to an anchor or structure. After securing the end of the safetywire to the ceiling, secure the other end to the camera using the screw that is fastened to thecamera.7 Connect the LAN cable to the camera through the wiring holeIf an AC adapter PA-V17 (optional) or external power supply is used, connect the powerconnector to the camera. Connect cables to external device I/O terminals and audio input/output terminals as necessary (see "Connecting the Camera" in VB-M40 Installation Guide).8 Mount the ceiling bracket on the ceilingPosition the ceiling bracket over the screws temporarily tightened in step 5, turn clockwise totemporarily secure in place, and completely fasten the screws.9 Attach the domeAlign the (O) mark on the dome with the (I) mark on the ceiling bracket, and turn clockwiseuntil the (I) mark on the dome aligns with the (I) mark on the ceiling bracket. This procedurealso aligns the ceiling bracket screw hole with the dome fixing screw hole.10 Affix the domeTo prevent the dome from rotating, attach one dome fixing screw (M2).11 Reboot the camera when the installation is completeThe camera position is initiated (see "Maintenance" in Chapter 4, "Setting Page" of the VB-M40Operation Guide).NoteWhile the LED is on, light may reflect inside the dome and be captured on video. If this happens, set theLED setting to [Off] (see “LED Setting” in VB-M40 Operation Guide).98642 35710Main SpecificationsModel DR40-C-VB/DR40-S-VBType Clear type/smoked typeNetwork camera-mounting environments Temperature -10 to 50°C (14 to 122°F), humidity 5 to 85%RH(non-condensing)Dimensions (Φ x H) 204 (112: Dome) x 92 mm (8.03 (4.41: Dome) x 3.62 in)*Including ceiling-embedded section: 176 mm (6.93 in) (H)Weight Approx. 765 g (1.687 lb) (excluding camera)Smoked (DR40-S-VB)This dome is approximately 50% transparent.Minimum subject illuminationDay Mode (color) : 0.8 lux (F1.6, Shutter Speed 1/30 sec., when Smart Shade Control is off)0.2 lux (F1.6, Shutter Speed 1/8 sec., when Smart Shade Control is off)0.06 lux (F1.6, Shutter Speed 1/8 sec., when Smart Shade Control is on)Night Mode (monochrome) : 0.02 lux (F1.6, Shutter Speed 1/30 sec., when Smart Shade Control is off)0.004 lux (F1.6, Shutter Speed 1/8 sec., when Smart Shade Control is off)0.002 lux (F1.6, Shutter Speed 1/8 sec., when Smart Shade Control is on)External DimensionsDR40-C-VB/DR40-S-VB Backside ceiling bracket204.0 mm (8.03 in)164.0 mm (6.46 in)112.0 mm (4.41 in)84.0 mm(3.31 in)92.0 mm(3.62 in)11Safety WireSecure to ananchor orstructureLAN cableCeilingbracketBacksideceilingbracketCeiling boardDomeCamera10.0 mm(0.39 in)7.0 mm (0.28 in)HeightBundledscrewM3 x 3BundledscrewM3 x 4BundledscrewM4 x 3 |
Related manuals for Canon DR40-C-VB
Canon Plenum SR30-P-VB Installation Manual
Canon BU-47H 1AM Installation Manual
Canon A2 Instructions Manual
Canon A2 Instructions Manual
Canon ST-E2 Instruction Manual
Canon pz-e1 Instruction Manual
Canon MA-52 Instructions Manual
Canon BG-E7 Instruction Manual
Canon motor drive mf Instruction Manual
Canon MA-200 Instructions Manual
manualsdatabase
Your AI-powered manual search engine