Canon L100 Service Manual

Also see for FAXPHONE L100: Basic operation guide Starter Guide Technical information

Contents

77 7-57-5Error Codes > FAX Error Code > Service Error Code > Error CodeError Codes > FAX Error Code > Service Error Code > Error CodeError code Details##763 at time of ECM transmission, the protocol signal has been transmitted more thanspecified after transmission of PPS-EOM, or T5 time-out (60 sec) has occurred.##764 at time of ECM transmission, the protocol signal has been transmitted more thanspecified after transmission of PPS-EOM.##767 at time of ECM transmission, DCN is received after transmission of PPS-EOP.##768 at time of ECM transmission, the protocol signal has been transmitted more thanspecified after transmission of PPS-EOP, or T5 time-out (60 sec) has occurred.##769 at time of ECM transmission, the protocol signal has been transmitted more thanspecified after transmission of PPS-EOP.##772 at time of ECM transmission, DCN is received after transmission of EOR-NULL.##773 at time of ECM transmission, the protocol signal has been transmitted more thanspecified after transmission of EOR-NULL, or T5 time-out (60 sec) has occurred.##774 at time of ECM transmission, ERR is received after transmission of EOR-NULL.##778 at time of ECM transmission, the protocol signal has been transmitted more thanspecified after transmission EOR-MPS, or T5 time-out (60 sec) has occurred.##779 at time of ECM transmission, ERR is received after transmission of EOR-MPS.##782 at time of ECM transmission, DCN is received after transmission of EOR-EOM.##783 at time of ECM transmission, the protocol signal has been transmitted more thanspecified after transmission of EOR-EOM, or T5 time-out (60 sec) has occurred.##784 at time of ECM transmission, the protocol signal has been transmitted more thanspecified due to message signal being unable to be received.##787 at time of ECM transmission, DCN is received after transmission of EOR-EOP.##788 at time of ECM transmission, the protocol signal has been transmitted more thanspecified after transmission of EOR-EOP, or T5 time-out (60 sec) has occurred.##789 at time of ECM transmission, ERR is received after transmission of EOR-EOP.##791 while ECM mode protocol is under way, a signal other than message signal isreceived.##794 at time of ECM reception, PPR with all 0s is received.##795 a fault has occurred in code processing for communication.● Transmission-related errorsError code Details##106 at time of reception, the protocol signal cannot be received for 6 sec while inwait for the signal.##107 at time of reception, the transmitting party cannot use fall-back.##114 at time of reception, RTN is transmitted.##200 at time of image reception, no carrier is detected for 5 sec.##228 image management information is abnormal.##237 decoding error has occurred.##671 at time of V.8 arrival, protocol fails to advance to phase 2 (probing) afterdetection of CM signal from caller, causing T1 time-out and releasing line##673 at time of V.34 transmission, the protocol does not advance from phase2 (probing) to phase 3 (training) and thereafter, causing T1 time-out andreleasing line.T-7-5Error code Details##675 at time of V.34 transmission, the protocol does not advance from phase 3(probing) and phase 4 (model parameter conversion) to the control channel(T.30 facsimile protocol) and thereafter, causing T1 time-out and releasingline.##790 at time of ECM reception, ERR is transmitted after reception of EOR-Q.##792 at time of ECM reception, PPS-NULL cannot be detected over partial pageprocessing.##793 at time of ECM reception, no effective frame is detected while high-speedsignal reception is under way, thus causing timeout.The error codes indicated by ## are output to report when “1” is set for “SSSW SW01 BIT0”(output of error code for service technicians) in service mode. Only “NG” is output at default.T-7-6