Carrier EDGE PRO 33CS2PP2S-01 Owner's Manual

Also see for EDGE Pro 33CS: Owner's manual Owner's manual Owner's manual

Contents

Carrier EDGE PRO 33CS2PP2S-01 Owner's Manual Manual pdf 4 page image

4around the date. To set the date (D), press the up buttonand stop on the desired date.3. If the month (M) needs to be changed, press the soft but-ton under the month on the screen. The selection box willmove to the month number. Press the up button to set thedesired month.4. Repeat this process to change the year (Y), if necessary.5. Press the done button. This will instruct the thermostat tobegin the Holiday schedule immediately.6. Close the thermostat door.Turning the Heating and Cooling System Off— To use the thermostat to turn the heating and cooling sys-tem off, perform the following:1. Open the thermostat door.2. Press the mode button until the display shows “off” in theupper left corner.3. Close the thermostat door.Changing the Humidity Level — The thermostatsoffer three humidity options: normal, auto, and off.The thermostat is set at the factory for “normal humidify,”which is a fixed humidity setting based on how much humiditythe user wants in the space. This humidity level remains con-stant, regardless of the outdoor temperature. The user can man-ually adjust the humidity level according to their own prefer-ences.The second option, “auto humidify,” uses an outdoor tem-perature sensor (if installed) to automatically adjust the indoorhumidity level according to the outside temperature.The third option is to turn off the humidify/dehumidifyfeature.To change the fixed (constant) humidity setting for normalhumidify, perform the following procedure:1. Open the thermostat door.2. The “humidify” icon will be displayed at the bottom ofthe screen when the operating mode is heat. The “dehu-midify” will be displayed when the operating mode iscool.3. Press the soft button under the humidify or dehumidifyicons. The screen will display the current setting.NOTE: A humidify icon will only be shown for33CS2PPRH thermostats.4. Press the up or down buttons to change the humidity set-ting. It is factory set at 26% for humidify and 60% for de-humidify. If there is too much condensation in the space,set the value to a lower number. If the air is too dry, set thevalue to a higher number. Humidity can be set to between10% and 46%. The dehumidify range is from 46% to98%.5. Close the thermostat door.To change the humidity setting for auto humidify, performthe following procedure:1. Open the thermostat door.2. The “humidify” icon will be displayed at the bottom ofthe screen. Press the soft button under the humidify icon.The screen will display the current setting.NOTE: A humidify icon will only be shown for33CS2PPRH thermostats.3. Press the mode button. An auto icon will appear at the topof the screen. The current humidity reading and the autohumidify set point will also be shown. The default autohumidify set point is 5.4. Press the up or down button to change the auto humidifysetting number (1 through 9). If there is too muchcondensation on the windows, select a number lower than5. If there seems to be a lot of static electricity, which of-ten means the air is too dry, select a number higher than 5.5. Close the thermostat door.To turn off the humidify or dehumidify feature open thethermostat door. Press the soft button under the humidify or de-humidify icons. Then press the mode button until the screendisplays OF. Close the themostat door.Using Emergency Heat — Emergency heat should beselected when it is desirable to heat the space with the auxiliaryheat only.To set the thermostat to use emergency heat, open the ther-mostat door. Press the mode button repeatedly until the arrowunder the button moves to the Em heat indicator on the screen.Close the thermostat door.Advanced Programming — The user can customizeseveral features of the thermostat. See Table 3.Table 3 — Configuration OptionsRESET REMINDERS — The thermostat will display whenit is time to change the UV (ultraviolet) light, change the filter,or perform scheduled maintenance to the equipment. When thereminder icons are displayed on the screen, pressing and hold-ing the done button for about 3 seconds will clear all reminders.This might not be the best option when multiple reminders areshown.The reminders can also be reset individually. To reset indi-vidual reminders, perform the following:1. Open the thermostat door.2. Press and hold the buttons underneath the heat and coolset points simultaneously. The screen will display “01”and up to three reset reminders (as have enabled by theinstaller). One of the reminders will flash. The displaywill show the percentage of time used by that reminderitem.3. Repeatedly press the set button until the reminder to becleared flashes.4. Press and hold the done button for about 3 seconds to re-move the reminder. The percentage associated with thereminder will be reset to zero.5. Press the done button again.6. Close the thermostat door.FAHRENHEIT OR CELSIUS DISPLAY — The thermostatis preset to display the temperature in degrees Fahrenheit. Theuser can change the display to Celsius if desired. To change thedisplay, perform the following:1. Open the thermostat door.2. Press and hold the buttons underneath the heat and coolset points simultaneously. The screen will display “01”and up to three reset reminders.3. Press the up arrow button until 01 changes to 02. The F(Fahrenheit) will also be displayed.4. Press the soft button under the F icon until C (Celsius)appears.OPTIONNUMBER CONFIGURATION01 Reset Reminders02 Fahrenheit/Centigrade Selection03 Backlighting04 Keypad Lockout05 Programmable/Nonprogrammable Selection06 Number of Programming Periods07 Unused08 Daylight Savings Time