Carrier TSTATCCNTT01-B Installation And Operating Instructions Manual

Carrier TSTATCCNTT01-B Installation And Operating Instructions Manual Manual pdf 1 page image

H_&COOMNG Non-Programmable ThermostatTSTATCCNTI'01-BVisit www.carrier.comInstallation and Operating InstructionsNOTE: Read the entire instruction manual before starting theinstallation.SAFETY CONSIDERATIONSImproper installation, adjustment, alteration, service, maintenance,or use can cause fire, electrical shock, or other conditions whichmay cause personal injury or property damage. Consult a qualifiedinstaller, for information or assistance. The qualified installer mustuse factory-authotized kits or accessories when modifying thisproduct. Refer to the individual instructions packaged with the kitsor accessories when installing.Follow all safety codes and wear safety glasses. Read theseinstructions thoroughly and follow all warnings or cautions at-tached to the unit. Consult local and state building codes and SheetMetal and Air Conditioning National Association (SMACNA) forspecial installation requirements.Recognize safety information. This is the safety-alert symbol ,_.When you see this symbol on the unit or in instructions andmanuals, be alert to the potential for personal injury.Understand the signal words DANGER, WARNING. and CAU-TION. These words are used with the safety-alert symbol. DAN-GER identifies the most serious hazards which will result in severepersonal injury or death. WARNING signifies hazards whichcould result in personal injury or death. CAUTION is used toidentify unsafe practices which would result in minor personalinjury or product and property damage.INTRODUCTIONCan-ier residential thermostats are waft-mounted, low-voltagethermostats which maintain room temperatnse by controlling theoperation of an HVAC (heating, ventilation and air conditioning)system. Separate heating and cooling set points and auto-changeover capability provides maximum comfort and flexibility.Some applications may require the addition of a jumper from RCto RH (see wiring diagrams). The thermostat comes factoryconfigured for air conditioner operation. See Fig. 1 for thermostatdimensions. During power interruption the internal memory storessettings indefinitely. Batteries are not required. The thermostatrequires 24 vac (both R and C terminals) to be connected forproper operation. The thermostat will not operate without therequired connections. (See Table 1). This AC Model (1-stage cool1-stage heat) thermostat is to be used for single-stage heatingand/or cooling applications only. This thermostat has separate heatand cool circuits. Some applications require the addition of ajumper from RC to RH. See applicable wiring diagram for moreinformation, This thermostat can be used with optional outdoortemperature' sensor.HEIGHT (IN.) I WIDTH (IN.) DEPTH (IN.)3-7/8 [ 5-3/4 1-7/16Fig. 1--Non Programmable ThermostatTable 1--Wiring Diagram ChartOUTDOOR UNIT1-Stage Fumace2-Stage FurnaceTypical Fan CoilVariable-Speed Fan CoilBoilerGasElectric HeatMODEL AC THERMOSTATSee Fig. 2See Fig. 3See Fig. 4See Fi_. 5See Fig, 6See Fig. 7See Fig. 8on a section of wall without pipes or ductworkThe thermostat should not be mount_l:• close to a window, on an outside wall, or next to a deer leadingto the outside• where exposed to direct light and heat from a lamp, the sun, afheplace, or any other temperature-radiating object which maycause a false reading• close to or in direct airflow from supply registers or return airgrilles• in areas with poor air circulation (such as behind a deer or inan alcove).Step 2_nstall ThermostatBefore installing thermostat, tam off all power to the unit.There may be more than one power disconnect. Electricalshock can cause injury or death.1, Turn off all power m unit.INSTALLATIONStep 1--Thermostat LocationThe thermostat should be mounted:approximately 5 ft from the fleer• close to or in a frequently used room, preferably on an insidepartitioning wallI2. If an existing thermostat is being replaced:a. Remove existing thermostat from the wall.b. Disconnect wires from existing thermostat. Do not allowwires to fall back into the wall. As each wire is discon-nected, record wire color and temfinal connection.c. Discard or recycle old themlostat.Manufacturer reserves the right to disr.ontlnue,o¢ change at any time, speclf_ations or designs wi/hout notice and without incurring oblig_ions.PC 101 CatalogNo. 03TS-TA33 Printed in U.S_. Form TSTAT-27SI 1 104)1 Replaces: NEWPg