Daikin ERGA04DAV3A Installer's Reference Manual

Also see for ERGA04DAV3: Installer's reference guide Installer's reference guide Installer's reference guide Installer's reference guide Installer's reference guide

Contents

Daikin ERGA04DAV3A Installer's Reference Manual Manual pdf 47 page image

8 ConfigurationInstaller reference guide47ERGA04~08DAV3(A) + EHVH/X04+08S18+23DADaikin Altherma – Low temperature split4P495248-1 – 2017.127.10 Finishing the outdoor unitinstallation7.10.1 To finish the outdoor unit installation1 Insulate and fix the refrigerant piping and interconnection cableas follows:fbaedca Gas pipeb Gas pipe insulationc Interconnection cabled Liquid pipee Liquid pipe insulationf Finishing tape2 Install the service cover.7.11 Finishing the indoor unitinstallation7.11.1 To close the indoor unit1 Close the cover of the switch box.2 Put the switch box back into place.3 Reinstall the top panel.4 Reinstall the side panels.5 Reinstall the front panel.6 Reconnect the cables to the user interface panel.7 Reinstall the user interface panel.NOTICEWhen closing the indoor unit cover, make sure that thetightening torque does NOT exceed 4.1 N•m.8 Configuration8.1 Overview: ConfigurationThis chapter describes what you have to do and know to configurethe system after it is installed.WhyIf you do NOT configure the system correctly, it might NOT work asexpected. The configuration influences the following:▪ The calculations of the software▪ What you can see on and do with the user interfaceHowYou can configure the system via the user interface.▪ First time – Configuration wizard. When you turn ON the userinterface for the first time (via the indoor unit), the configurationwizard starts to help you configure the system.▪ Restart the configuration wizard. If the system is alreadyconfigured, you can restart the configuration wizard. To restart theconfiguration wizard, go to Installer settings > Configurationwizard. To access Installer settings, see "8.1.1 To access themost used commands" on page 47.▪ Afterwards. If necessary, you can make changes to theconfiguration in the menu structure or the overview settings.INFORMATIONWhen the configuration wizard is finished, the userinterface will show an overview screen and request toconfirm. When confirmed, the system will restart and thehome screen will be displayed.Accessing settings – Legend for tablesYou can access the installer settings using two different methods.However, NOT all settings are accessible via both methods. If so,the corresponding table columns in this chapter are set to N/A (notapplicable).Method Column in tablesAccessing settings via the breadcrumb in themenu structure. To enable breadcrumbs,press the button in the home screen.#Accessing settings via the code in theoverview field settings.CodeSee also:▪ "To access the installer settings" on page 47▪ "8.6 Menu structure: Overview installer settings" on page 768.1.1 To access the most used commandsTo change the user permission levelYou can change the user permission level as follows:1 Go to [B]: User profile.2 Enter the applicable code for the user permission. —▪ Move the cursor from left to right.▪ Browse through the list of digits and change theselected digit.▪ Confirm the pincode and proceed.Installer pin codeThe Installer pin code is 5678. Additional menu items and installersettings are now available.5678InstallerAdvanced user pin codeThe Advanced user pin code is 1234. Additional menu items for theuser are now visible.User pin codeThe User pin code is 0000.To access the installer settings1 Set the user permission level to Installer.2 Go to [9]: Installer settings.To modify an overview settingExample: Modify [1‑01] from 15 to 20.All settings can be done using the menu structure. If for any reason itis required to change a setting using the overview settings, then theoverview settings can be accessed as follows:1 Set the user permission level to Installer. See "Tochange the user permission level" on page 47.—2 Go to [9.I]: Installer settings > Overview fieldsettings.Final English - Tanslations in progress