Daikin RZQG71L8V1B Installation Manual

Daikin RZQG71L8V1B Installation Manual Manual pdf 20 page image

Installation manual17 RZQG71~140L + RZQSG100~140LSplit system air conditioners4P339538-1A – 2014.0314.3. Precautions on wiring of power supply and inter-unit wiring Use a round crimp-style terminal for connection to the powersupply terminal board. In case it cannot be used due tounavoidable reasons, be sure to observe the followinginstruction.- Do not connect wires of different gauge to the same powersupply terminal. (Looseness in the connection may causeoverheating.)- When connecting wires of the same gauge, connect themaccording to the below figure. Use the correct screwdriver to tighten the terminal screws.Small screwdrivers can damage the screw head and preventappropriate tightening. Over-tightening the terminal screws can damage the screws. See the table below for tightening torques for the terminalscrews. Refer to the installation manual attached to the indoor unit forwiring of indoor units, etc. Attach an earth leakage breaker and fuse to the power supplyline. (See figure 9)I PairII TwinIII TripleIV Double twinM MasterS Slave1 Earth leakage breaker2 Fuse3 Remote controller In wiring, make certain that prescribed wires are used, carry outcomplete connections, and fix the wires so that outside forcesare not applied to the terminals.14.4. Specifications of standard wiring componentsOnly for RZQ(S)G*V1 + RZQSG100+125Y1:Equipment complying with EN/IEC 61000-3-12(1).Only for RZQG100~140Y1 + RZQSG140Y1:Point for attention regarding quality of the public electricpower supplyThis equipment complies with EN/IEC 61000-3-12(1) providedthat the short-circuit power Ssc is greater than or equal to1170 kVA at the interface point between the user's supply andthe public system.It is the responsibility of the installer or user of the equipment toensure, by consultation with the distribution network operator ifnecessary, that the equipment is connected only to a supply witha short-circuit power Ssc greater than or equal to 1170 kVA.Above indicated value is the most stringent value. Refer todatabooks for specific product-data.Tightening torque (N•m)M4 (X1M) 1.2~1.8M4 (EARTH) 1.2~1.4M5 (X1M) 2.0~3.0M5 (EARTH) 2.4~2.91 2 31 Round pressure terminal2 Cut out section3 Cup washerRZQG 71V1 100V1 125V1 140V1 71Y1 100Y1 125Y1 140Y1Minimum circuitamps (MCA)(a)(a) Stated values are maximum values (see electrical data of combination withindoor units for exact values).20.6 32.0 33.5 14.0 21.0 22.5Recommendedfield fuse (A) 25 40 16 25Wire type(b)(b) Only in protected pipes, use H07RN-F when protected pipes are not used.H05VV-U3G H05VV-U5GSize Wiring size must comply withthe applicable local and national codeWire type of wiringbetween the units H05VV-U4G2.5RZQSG 100V1 125V1 140V1 100Y1 125Y1 140Y1Minimum circuitamps (MCA)(a)(a) Stated values are maximum values (see electrical data of combination withindoor units for exact values).32.0 33.5 17.7 19.2 22.5Recommendedfield fuse (A) 40 20 25Wire type(b)(b) Only in protected pipes, use H07RN-F when protected pipes are not used.H05VV-U3G H05VV-U5GSize Wiring size must comply withthe applicable local and national codeWire type of wiringbetween the units H05VV-U4G2.5CAUTION Select all cables and wire sizes in accordance withapplicable legislation. After finishing the electrical work, confirm that eachelectric part and terminal inside the electric part box isconnected securely. The earth leakage breaker must be a high-speed typebreaker of 30 mA (<0.1 s).(1) European/International Technical Standard setting the limits for harmoniccurrents produced by equipment connected to public low-voltage systemswith input current >16 A and ≤75 A per phase.