Daikin VRV III-S Installation Manual

Also see for VRV III-S: Operation manual Operation manual Technical data

Contents

Daikin VRV III-S Installation Manual Manual pdf 22 page image

Installation manual19 RXYSQ4~6P7V3B + RXYSQ4~6P7Y1BVRVIII-S system air conditioner4PW35338-13.2 Possible settings for function CThe noise of level 3< level 2< level 1 ( ).3.3 Possible settings for function D and EFor function D ( ) only: the noise of level 3<level 2< level 1 ( ).For function E ( ) only: the power consumption oflevel 1< level 2 < level 3 ( ).4 Push the button and the setting is defined.5 When the button is pushed again, the operationstarts according to the setting.Refer to the service manual for more details and for other settings.Confirmation of the set modeThe following items can be confirmed by setting mode 1 (H1Pled is off)Check the led indication in the field marked .1 Indication of the present operation state2 Indication of COOL/HEAT selection setting3 Indication of low noise operation state4 Indication of power consumption limitation setting12.4. Test operation■ Check the stop valvesMake sure to open the gas and liquid line stop valves.■ After installation, perform the test operation.Unless the test operation is performed, the error code "U3" isshown on the remote controller and the unit cannot be operated.Performing the test operation1 To protect the compressor, make sure to turn on the powersupply 6 hours before starting operation.2 Set to setting mode 1 (H1P led is off) (refer to "Setting mode 1"on page 18).3 Press the button for 5 seconds when the unit is at astandstill. The test operation starts when the H2P led blinks andthe remote controller indicates (test operation) and(external control).It may take 10 minutes to bring the state of refrigerant uniformbefore the compressor starts, but that is not a malfunction.The test operation is automatically carried out in cooling modeduring 15~30 minutes.Depending on the situation, the refrigerant running sound or thesound of a magnetic solenoid valve may rise during thisoperation.The following items are automatically checked:- Check for incorrect wiring- Check if stop valves are open- Check of refrigerant charge- Automatic judgement of piping length4 After the test operation (maximum 30 minutes), the unitautomatically stops. Check the operation results by the outdoorunit led indication.H1P H2P H3P H4P H5P H6P H7POFF(*)(*) This setting = factory setting.w x x x x x xw x x x x x cw x x x x c xw x x x x c cH1P H2P H3P H4P H5P H6P H7Pw x x x x x c(*)(*) This setting = factory setting.w x x x x c xw x x x c x xNOTE When finished, please mark the settings of function C,D and E in the "Records" part of the label on thebackside of the front plate.x normalw abnormalc under preparation or under test operationH1P H2P H3P H4P H5P H6P H7Px x w x x x x1 When set to COOL/HEAT change-over by each individual outdoorunit circuit (= factory setting).2 Indication on master unit when COOL/HEAT change-over iscarried out by outdoor units connected in multiple system-combination.3 Indication on slave unit when COOL/HEAT change-over is carriedout by outdoor units connected in multiple system-combinationH1P H2P H3P H4P H5P H6P H7P1(*)(*) This setting = factory setting.x x w x x x x2 x x x w x x x3 x x x x w x x1123L.N.O.P1DEMAND3123BS3 RETURNBS3 RETURNx standard operation (= factory setting)w operationH1P H2P H3P H4P H5P H6P H7Px x w x x x xx standard operation (= factory setting)w operationH1P H2P H3P H4P H5P H6P H7Px x w x x x xNOTE After turning on the power supply, the unit can not bestarted until the H2P initialisation led goes off(maximum 12 minutes).NOTE When you want to terminate the test operation,press the button. The unit will keeprunning for 30 seconds and then stops. Duringtest operation it is impossible to stop the unit withthe remote controller.H1P H2P H3P H4P H5P H6P H7Pnormal x x w x x x xabnormal x w x x x x xL.N.O.PL.N.O.PDEMANDDEMANDBS4 TESTBS3 RETURN