Danfoss VLT AutomationDrive FC 302 Design Manual
Also see for VLT AutomationDrive FC 302: Service guideProgramming guideInstruction manualInstallation guideOperating guide
                                                                                                                                                                                                                    | |
Contents
| 
ParametersFC+24 V+24 VD IND IND INCOMD IND IND IND IN+10 VA INA INCOMA OUTCOM12131819202729323337505354554239130BB930.10Function SettingParameter 1-29Automatic MotorAdaptation(AMA)[1] Enablecomplete AMAParameter 5-12 Terminal 27Digital Input[0] Nooperation*=Default valueNotes/comments: Setparameter group 1-2* MotorData according to motornameplate.Table 12.2 Wiring Configuration for AMA withoutT27 Connected12.3 Wiring Configurations for AnalogSpeed ReferenceParameters+10 VA INA INCOMA OUTCOM505354554239A53U - I0 – 10 V+-e30bb926.11FCFunction SettingParameter 6-10 Terminal 53 LowVoltage0.07 V*Parameter 6-11 Terminal 53 HighVoltage10 V*Parameter 6-14 Terminal 53 LowRef./Feedb. Value0 RPMParameter 6-15 Terminal 53 HighRef./Feedb. Value1500 RPM*=Default valueNotes/comments:Table 12.3 Wiring Configuration for Analog Speed Reference(Voltage)Parameters+10 VA INA INCOMA OUTCOM505354554239+-FCe30bb927.11A53U - I4 - 20mAFunction SettingParameter 6-12 Terminal 53 LowCurrent4 mA*Parameter 6-13 Terminal 53 HighCurrent20 mA*Parameter 6-14 Terminal 53 LowRef./Feedb. Value0 RPMParameter 6-15 Terminal 53 HighRef./Feedb. Value1500 RPM*=Default valueNotes/comments:Table 12.4 Wiring Configuration for Analog Speed Reference(Current)12.4 Wiring Configurations for Start/StopParametersFC+24 V+24 VD IND IND INCOMD IND IND IND IN+10A INA INCOMA OUTCOM12131819202729323337505354554239130BB802.10Function SettingParameter 5-10 Terminal 18Digital Input[8] Start*Parameter 5-12 Terminal 27Digital Input[0] NooperationParameter 5-19 Terminal 37 SafeStop[1] SafeTorque OffAlarm*=Default valueNotes/comments:If parameter 5-12 Terminal 27Digital Input is set to [0] Nooperation, a jumper wire toterminal 27 is not needed.Table 12.5 Wiring Configuration for Start/Stop Command withSafe Torque OffApplication Examples Design GuideMG38C202 Danfoss A/S © 01/2018 All rights reserved. 18512 12 |
Related manuals for Danfoss VLT AutomationDrive FC 302
Danfoss VLT AutomationDrive FC 300 Design Manual
Danfoss VLT AutomationDrive FC 300 Design Manual
Danfoss VLT AutomationDrive FC 300 Design Manual
Danfoss VLT AutomationDrive FC 300 Design Manual
Danfoss VLT AutomationDrive FC 301 Design Manual
Danfoss VLT AutomationDrive FC 360 Design Manual
Danfoss VLT AutomationDrive FC 360 Design Manual
Danfoss VLT AutomationDrive FC 301 Series Design Manual
Danfoss VLT AutomationDrive FC 300 Manual
Danfoss VLT AutomationDrive FC 361 Series Design Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine