Danfoss VLT FC 101 Quick Manual

Also see for VLT HVAC Basic Drive FC 101: Quick guide Design guide Quick guide Programming guide Quick guide

Danfoss VLT FC 101 Quick Manual Manual pdf 45 page image

6 Specifications6.1 Mains Supply6.1.1 3x200–240 V ACFrequency converter PK25 PK37 PK75 P1K5 P2K2 P3K7 P5K5 P7K5 P11K P15K P18K P22K P30K P37K P45KTypical shaft output [kW] 0.25 0.37 0.75 1.5 2.2 3.7 5.5 7.5 11.0 15.0 18.5 22.0 30.0 37.0 45.0Typical shaft output [hp] 0.33 0.5 1.0 2.0 3.0 5.0 7.5 10.0 15.0 20.0 25.0 30.0 40.0 50.0 60.0Protection rating IP20 H1 H1 H1 H1 H2 H3 H4 H4 H5 H6 H6 H7 H7 H8 H8Maximum cable size interminals (mains, motor)[mm2 (AWG)]4(10)4(10)4(10)4(10)4(10)4(10)16(6)16(6)16(6)35(2)35(2)50(1)50(1)95(0)120(4/0)Output current40 °C (104 °F) ambient temperatureContinuous(3x200–240 V) [A] 1.5 2.2 4.2 6.8 9.6 15.2 22.0 28.0 42.0 59.4 74.8 88.0 115.0 143.0 170.0Intermittent(3x200–240 V) [A] 1.7 2.4 4.6 7.5 10.6 16.7 24.2 30.8 46.2 65.3 82.3 96.8 126.5 157.3 187.0Maximum input currentContinuous3x200–240 V) [A] 1.1 1.6 2.8 5.6 8.6/7.214.1/12.021.0/18.028.3/24.041.0/38.2 52.7 65.0 76.0 103.7 127.9 153.0Intermittent(3x200–240 V) [A] 1.2 1.8 3.1 6.2 9.5/7.915.5/13.223.1/19.831.1/26.445.1/42.0 58.0 71.5 83.7 114.1 140.7 168.3Maximum mains fuses SeeEstimated power loss [W],Best case/typical1)12/1415/1821/2648/6080/10297/120182/204229/268369/386 512 697 879 1149 1390 1500Weight enclosureprotection rating IP20 [kg(lb)]2.0(4.4)2.0(4.4)2.0(4.4)2.1(4.6)3.4(7.5)4.5(9.9)7.9(17.4)7.9(17.4)9.5(20.9)24.5(54)24.5(54)36.0(79.4)36.0(79.4)51.0(112.4)51.0(112.4)Efficiency [%], best case/typical2)97.0/96.597.3/96.898.0/97.697.6/97.097.1/96.397.9/97.497.3/97.098.5/97.197.2/97.1 97.0 97.1 96.8 97.1 97.1 97.3Output current50 °C (122 °F) ambient temperatureContinuous(3x200–240 V) [A] 1.5 1.9 3.5 6.8 9.6 13.0 19.8 23.0 33.0 41.6 52.4 61.6 80.5 100.1 119Intermittent(3x200–240 V) [A] 1.7 2.1 3.9 7.5 10.6 14.3 21.8 25.3 36.3 45.8 57.6 67.8 88.6 110.1 130.9Table 6.1 3x200–240 V AC, 0.25–45 kW (0.33–60 hp)1) Applies for dimensioning of frequency converter cooling. If the switching frequency is higher than the default setting, the power losses mayincrease. LCP and typical control card power consumptions are included. For power loss data according to EN 50598-2, refer to www.danfoss.com/vltenergyefficiency.2) Efficiency measured at nominal current. For energy efficiency class, see chapter 6.3.12 Ambient Conditions. For part load losses, seewww.danfoss.com/vltenergyefficiency.Specifications Quick GuideMG18A802 Danfoss A/S © 05/2016 All rights reserved. 436 6