DeLonghi EC9335.M Manual

Also see for La Specialista EC9335M: Instructions

29B6. Hot water buttonB7. button: to customise beverage quantityB8. Mode selector dial:• Espresso• Americano• Coffee• DescalingB9. Descale lightB10. Steam ready lightB11. Overtemperature lightB12. Energy saving lightB13. General alarm lightB14. Beans container empty/No beans container lightB15. No water lightB16. Pressing lightB17. Pressure gauge1.3 Description of the accessories(page 3 - C )C1. Filter holderC2. Easy Clean filter 1 coffeeC3. Easy Clean filter 2 coffeeC4. "Total Hardness Test" indicator paperC5. DescalerC6. Water softener filter (*if present)C7. Power cordC8. Tube brushC9. Milk jug2. PREPARING THE APPLIANCEWash all accessories with warm water and washing-up liquid,then proceed as follows:1. Insert the beans container (A2) in the coffee mill (fig. 1).The container is correctly inserted when the arrow is linedup with the symbol and you hear a “click”;2. Insert the drip tray (A13) complete with cup grill (A11) anddrip tray grille (A12) (fig. 2);3. Extract the water tank (A17) (fig. 3) and fill with fresh cleanwater, taking care not to exceed the MAX level (fig. 4).4. Put the tank back in the appliance.Important: Never operate the appliance without water in the tank or without thetank.Please note: You should customise water hardness as soon as possible following theinstructions in section "12.2 Water hardness".3. SETTING UP THE APPLIANCE1. Plug the power cord connector (C7) into the socket (A19) atthe back of the appliance (fig. 5), then plug the plug intothe mains socket. Make sure the main switch (A20) at theback of the appliance is pressed and in the I position (fig.6);2. The light corresponding to the button (B6) comes onand the light (B15) flashes to indicate that you need todeliver water to fill the circuit (fig. 7);3. Place a container with a minimum capacity of 100 ml underthe hot water spout (A5) and cappuccino maker (A8) (fig.8);4. Press the button (B6) corresponding to the light (fig.9). Delivery begins and stops automatically. Empty thecontainer.Before using the machine, you must rinse the internal circuits.Proceed as follows:5. Attach the filter holder (C1) complete with filter to the ap-pliance. To attach correctly, align the filter holder handlewith (fig. 10), then turn the handle to the right until itis aligned in the position;6. Place a recipient under the filter holder and cappuccinomaker (A8) (fig. 11);7. Press the button (B4) corresponding to the light. De-livery begins (fig. 12);8. When delivery is complete, turn the steam dial (A4) (fig.13) and deliver steam for 10 seconds to rinse the steamcircuit;9. Repeat points 7 and 8 until you have delivered at least 1litre of water (about half the tank);10. Extract the water tank (A17) (fig. 3), rinse and fill with freshclean water, taking care not to exceed the MAX level (fig. 4).The appliance is ready for use.Please note: We also recommend rinsing the internal circuits if the appliance isnot used for a long period.The first time you use the appliance, you need to make 4-5 cupsof coffee before the appliance starts to give satisfactory results.Pay particular attention to the quantity of pre-ground coffee inthe filter ((C2) or (C3)) (see instructions in section "4.5 Adjustingthe quantity of ground coffee in the filter").Proceed as described in section "4. Prepare the perfect dose".4. PREPARE THE PERFECT DOSE4.1 Preparing the coffee mill1. Make sure the beans container is correctly inserted andlined up to position "3" (fig. 14) (default setting) ;2. Remove the beans container lid (A1);3. Place the required quantity of coffee beans in the container(fig. 15);4. Close the lid, pressing firmly.5. The first time you use the appliance, make sure the dial (B2)is in the position (default setting).4.2 Select the grinding levelThe grinding level affects delivery speed and therefore the qual-ity of the extract.