Dell PowerVault 122T SDLT 320 User Manual

Also see for PowerVault 122T SDLT 320: Handbook

Dell PowerVault 122T SDLT 320 User Manual Manual pdf 3 page image

Autoloader Operating ModesOverviewThe operating mode is set based on whether you have automation software controlling cartridges in the autoloader or if you are manually loading andunloading cartridges using the autoloader Operator's Panel commands. The autoloader always operates in Autodetect Mode, which is transparent to you. InAutodetect Mode, the autoloader automatically assumes that you are not using an automation software package to control cartridge or drive activity. This iscalled Stacker or Sequential Mode. If the autoloader detects that an automation software package is controlling tape/drive activity, it will automatically switchto Random Mode.Random ModeThis is the normal mode of operation when a backup software application is being used. In Random Mode, the autoloader will not automatically load tapes intothe drive; it instead waits for commands from the software. To use Random Mode, you do not need to configure anything from the autoloader front panel, butyour backup software package must support autoloaders, which often requires the additional installation of an autoloader/library software module.Sequential ModeSequential Mode is useful when an adequate software application is not available. In Sequential Mode, the autoloader will automatically unload and loadtapes from the drive. The operator determines the first tape to load by loading the desired tape into the tape drive using the autoloader's front panel controls(see "Loading Cartridges"). When the first tape is full or unloaded for any other reason, the autoloader automatically removes the tape from the drive, puts itin its original slot, then loads the next available higher numbered slot, continuing this sequence with each available higher numbered slot. To furtherdetermine how you want tapes loaded into the autoloader's tape drive while in Sequential Mode, you may set Circular and Autoload options from theautoloader front panel. When the autoloader is in Sequential Mode, the LCD will display SEQ in the lower-right corner of the display.Circular Mode On/OffThis option turns Circular Mode on or off, and it is only used when in Sequential Mode. When Circular Mode is on, after the autoloader has cycled through allavailable cartridges, it then reloads the original first cartridge in the sequence. If Circular Mode is turned off and the last cartridge has been unloaded, theautoloader stops loading cartridges until you manually load another cartridge.To access this option, follow these steps:1. From the Home screen or main menu, press + or - until Configuration appears on the top line of the LCD screen, and then press Enter.2. Press + or - until Circular Mode appears on the LCD screen. The second line on the LCD screen indicates the current status, either On or Off.3. Press Enter. The LCD screen indicates whether you are about to turn Circular Mode on or off.4. Press Enter to accept the change to Circular Mode or press Cancel to exit and not save the changes.Autoload Mode On/OffThis option turns Autoload Mode on or off, and it is only used when in Sequential Mode. When Autoload Mode is on, the autoloader automatically loads thecartridge from the lowest-numbered full slot into the tape drive when powered on. It then follows standard sequential operation as described above.To access this option, follow these steps:1. From the Home screen or main menu, press + or - until Configuration appears on the top line of the LCD screen, and press Enter.2. Press + or - until Autoload Mode appears on the LCD screen. The second line on the LCD screen indicates the current status, either On or Off.3. Press Enter.The LCD screen indicates whether you are about to turn Autoload Mode on or off.4. Press Enter to accept the change to Autoload Mode or press Cancel to exit without saving the changes.Updating FirmwareUsing a Firmware Upgrade TapeThis option performs a firmware code update on the tape drive using a firmware upgrade cartridge. Note that this technique upgrades the tape drive only, andcannot be used to upgrade the autoloader robotics. To update the autoloader robotics (see "Using SCSI ").NOTE: If you changed either SCSI ID, you may also need to reboot the host server and reconfigure your backup software before youcan use the autoloader. Consult your hardware and software manuals for more information.NOTICE: Use caution when choosing Circular Mode as it makes it possible to write over data on previously written cartridges.NOTICE: Regardless of the firmware update technique, do not power cycle or reset the autoloader during the upgrade process.Doing so could cause the autoloader to become inoperable.NOTE: This code update operation assumes that the upgrade tape is imported as part of this procedure. Do not import the firmwareupdate cartridge before starting this procedure.