Denon AVR-2803 Operating Instructions Manual

Also see for AVR-2803: Service manual Operating instructions Brochure & specs Control protocol Code List

Denon AVR-2803 Operating Instructions Manual Manual pdf 9 page image

9ENGLISHRemote control unit• For details on the functions of these parts, refer to the pages given in parentheses ( ).SYSTEM CALL buttons................(20)ON SCREEN/DISPLAY button ..(19, 25)Cursor buttons ...............................(9)TEST TONE button ......................(27)System buttons ...............(18, 19, 21)ZONE 2 buttons ...........................(26)MODE SELECT button ................(18)Input source selectorbuttons ....(18, 19, 23, 26, 30, 35~37)SYSTEM SETUP/SETUPbutton ..........................(9, 10, 17, 19)Mode selectorbuttons ............................(18~22, 26)Surround buttons............................(23, 24, 28~30, 32)ZONE 1/MAIN buttons.................(26)Power buttons .......................(18~22)Tuner system/Systembuttons ................(18, 19, 26, 35~37)MUTING button ...........................(25)Master volume controlbuttons...................................(23, 26)RDS/RETURN button.(18, 19, 36~38)Remote control signaltransmitter ...................................(17)7 SETTING UP THE SYSTEM• Once all connections with other AV components have been completed as described in “CONNECTIONS”(see pages 4 to 8), make the various settings described below on the monitor screen using the AVR-2803’son-screen display function.These settings are required to set up the listening room’s AV system centered around the AVR-2803.• Check that the remote control unit is set to AMP mode (TAPE, CDR/MD or CD).• The system settings can be reset to the default (factory shipment) settings by initialization of themicroprocessor (see page 38).• Use the following buttons to set up the system:SYSTEM SETUP buttonPress this to display the system setup menu.ENTER buttonPress this to switch the display.Also use this button to complete the setting.CURSOR buttons0 and 1: Use these to move the cursors (0 and 1) tothe left and right on the screen.• and ª: Use these to move the cursors (• and ª) tothe up and down on the screen.• System setup items and default values (set upon shipment from the factory)INPUT MODE selectorbuttons...................................(23, 24)SURROUND PARAMETERbutton ..................(19, 28~30, 32, 33)CH SELECT/ENTER button.....................................(9, 19. 27, 28)SURROUND BACK button...........(30)LED (indicator)..............................(20)USE/LEARN button................(20, 21)FRONT SPEAKER button.............(22)System setup Default settingsyerSpeakerConfigurationSubwoofermodeDolby DigitalSetupChannelLevelDigital InAssignmentInput the combination of speakers in yoursystem and their corresponding sizes (Small forregular speakers, Large for full-size, full-range) toautomatically set the composition of the signalsoutput from the speakers and the frequencyresponse.This selects the subwoofer speaker for playingdeep bass signals.Turn the audio compression on or off when down-mixing Dolby Digital signals.This adjusts the volume of the signals output fromthe speakers and subwoofer for the differentchannels in order to obtain optimum effects.This assigns the digital input jacks for thedifferent input sources.InputsourceDigitalInputsFront Sp.LargeCenter Sp. Surround Sp.Sub WooferSmall SmallYesLFEFront L & R Center Surround L & RSub Woofer3.6 m (12 ft) 3.6 m (12 ft) 3.0 m (10 ft)3.6 m (12 ft)Front L Front R Center SurroundRSurroundBack R Subwoofer0 dB 0 dB 0 dB 0 dB 0 dB 0 dBCD DVD VDP TV DBS TAPECOAX1 COAX2 OPT1 OPT2 OPT3 OPT4Surround BackSp.Small / 2spkrsOFFw Delay TimeThis parameter is for optimizing the timing withwhich the audio signals are produced from thespeakers and subwoofer according to the listeningposition.SBL & SBR3.0 m (10 ft)SurroundBack L0 dBSurroundL0 dBVCR-1OFFV. AUXOFFqCrossoverFrequencySet the frequency (Hz) below which the bass soundof the various speakers is to be output from thesubwoofer.80 HzVCR-2OFFt Video InAssignmentThis assigns the color difference (component)video input jacks for the different input sources.DVD VDP TV VCR-1 V. AUX —VIDEO1 NONE NONE NONE NONE —VCR-2NONEDBSVIDEO2Set this to switch the surround backchannel’s power amplifier for usefor zone 2.Surround BackPower AMPAssignmentThis sets the output level for thezone 2 output jacks. VariableZone2 vol.Levelu Zone2ControlNOTE:• The shaded button does not function with the AVR-2803. (Nothing happens when they are pressed.)