Denon AVR-E200 Service Manual

Also see for AVR-E200: Owner's manual Getting started Service manual Getting started

Contents

7NOTE FOR SCHEMATIC DIAGRAMWARNING:Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.CAUTION:Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. Ifthe leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the setis defective.WARNING:DO NOT return the set to the customer unless the problem is identified and remedied.NOTICE:ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHMALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P INDICATES MICRO-MICROFARAD. EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECTTO CHANGE WITHOUT PRIOR NOTICE.NOTE FOR PARTS LISTParts indicated by "nsp" on this table cannot be supplied.When ordering a part, make a clear distinction between "1" and "I" (i) to avoid mis-supplying.A part ordered without specifying its part number can not be supplied.General-purpose Carbon Chip Resistors are not included are not included in the P.W.Board parts list.(Refer to the Schematic Diagram for those parts.)Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)Part indicated by "★" mark is not illustrated in the exploded view.WARNING:1.2.3.4.5.6.● ResistorsRD : CarbonRC : CompositionRS : Metal oxide filmRW: windingRN : Metal filmRK : Metal mixtureP : Pulse-resistant typeNL : Low noise typeNB : Non-burning typeFR : Fuse-resistorF : Lead wire forming2B : 1/8 W2E : 1/4 W2H : 1/2 W3A : 1 W3D : 2 W3F : 3 W3H : 5 WF : ±1%G : ±2%J : ±5%K : ±10%M : ±20%Ex.: RNType14KShapeand per-formance2EPower182Resist-anceGAllowableerrorFROthers* Resistance1800ohm=1.8kohm1 8 2Indicates number of zeros after effective number.2-digit effective number.1.2ohm1 R 22-digit effective number, decimal point indicated by R.1-digit effective number.: Units: ohm● CapacitorsCE : Aluminum foilelectrolyticCA : Aluminium solidelectrolyticCS : Tantalum electrolyticCQ : FilmCK : CeramicCC : CeramicCP : OilCM: MicaCF : MetallizedCH : MetallizedHS : High stability typeBP : Non-polar typeHR : Ripple-resistant typeDL : For change and dischargeHF : For assuring high frequencyU : UL partC : CSA partW : UL-CSA partF : Lead wire forming0J : 6.3 V1A : 10 V1C : 16 V1E : 25 V1V : 35 V1H : 50 V2A : 100 V2B : 125 V2C : 160 V2D : 200 V2E : 250 V2H : 500 V2J : 630 VF : ±1%G : ±2%J : ±5%K : ±10%M : ±20%Z : ±80%: - 20%P : +100%C : ±0.25pFD : ±0.5pF= : OthersEx.: CEType04WShapeand per-formance1HDielectricstrength3R2CapacityMAllowableerrorBPOthers･ Units:μF.2200μF2 2 2Indicates number of zeros after effective number.2-digit effective number.･ Units:μF.2.2μF2 R 22-digit effective number, decimal point indicated by R1-digit effective number.* Capacity (electrolyte only)･ When the dielectric strength is indicated in AC,"AC" is included after the dielectric strength value.* Capacity (except electrolyte)･ Units:pF2200pF=0.0022μF2 2 2Indicates number of zeros after effective number. (More than 2)2-digit effective number. ･ Units:pF220pF2 2 12-digit effective number.Indicates number of zeros after effective number. (0 or 1)NOTE FOR PARTS LIST