Denon RCD-M33 Operating Instructions Manual

Also see for RCD-M33: Specification Operating instructions Operating instructions Operating instructions Service manual

Contents

Denon RCD-M33 Operating Instructions Manual Manual pdf 10 page image

10ENGLISH• The supplied remote control unit (RC-999) is for use with the RCD-M33 unit only.• If the cassette deck (DRR-M33) is connected to the main unit, you may operate each of the abovecomponents using its respective remote control unit (refer to pages 10, 11).7 REMOTE CONTROL UNIT(1) Inserting the batteriesq Open the battery compartment cover of theremote control unit.Press the knob and open the cover in thedirection of the arrow.w Insert the two R03 (AAA) batteries, followingthe + and – marks in the battery compartment.e Close the cover of the battery compartment.Cautions on Batteries• Use R03 (AAA) batteries in this remotecontrol unit.• Replace the batteries with new ones afterapproximately 1 year, though this dependson the frequency with which the remotecontrol unit is used.• Replace the batteries with new ones if theunit does not operate when the remotecontrol unit is operated from nearby, even ifthe batteries are less than a year old.• Be sure to insert the batteries in the properdirection, following the “ < ” and “ > ”marks in the battery compartment.• To avoid damage or leakage of battery fluid:• Do not use a new battery with an old one.• Do not use two different types of batteries.• Do not short-circuit, take apart, heat ordispose of batteries in flames.• Remove the batteries when you do not planto use the remote control unit for anextended period of time.• If the battery fluid should leak, carefully wipeoff the fluid from the inside of the batterycompartment, then insert new batteries.(2) Using the Remote Control Unit• The remote sensor is located on the CD receiver.Point the remote control unit at the remotesensor as shown on the diagram when operatingit.• The remote control unit will operate from adirect distance of approximately 7 meters, butthis distance will be shortened if obstacles arepresent or if operated at an angle. (The remotecontrol unit will operate at an angle of up to 30°in either direction.)7m30∞30∞NOTES:• The remote control unit may not operate ifthe remote sensor is exposed to directsunlight or the strong light from a lightingfixture, or if there is an obstacle between theremote control unit and the remote sensor.• Do not press buttons on the remote controlunit and on the set at the same time. Doingso could result in malfunctions.• If the remote control unit is pointed awayfrom the re-mote sensor during continuousoperations (such as when turning the volumeup or down), the operation will stop. If thishappens, point the remote control unit at theremote sensor and press the button again.The RCD-M33 comes with a system remote control unit (RC-999).qe #5wrty uio!0!1!2!3!4!5 !6!7 !8 !9 @0@1 @2@3@4@5@6 @7@8@9#0#1#2#3 #4(3) Remote Control Unit Part Names and Functionsq SLEEP button• Press this button to set the sleep timer.w OFF button• Use this switch to set the power toSTANDBY mode.e TUNER button• Press this button to set the functionTUNER mode.r CD button• Press this button to set the function CDmode.t PROG/DIRECT button• Press this button to switch betweenPROGRAM and DIRECT play.y EDIT buttonIn CD function :• Press this button for edited recording on atape, dividing the tracks onto sides A andB according to the length of the tape.In TUNER function :• Press this button to input the stationname.u CALL button• Use this button to confirm theprogrammed song.i Number buttonsIn CD function :• Press these buttons to specify thedesired track.In TUNER function :• Press these buttons to recall presetstation.o FOLDER (+/–) buttonFor MP3/WMA discs with the function setto CD:• Select the folder.• In the play and pause modes, the firsttrack in the selected folder is selected.