Desa EFP33NR Owner's Operation And Installation Manual

Also see for Comfort Glow CGEFP33NR: OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL

108117-01HFor more information, visit www.desatech.comFor more information, visit www.desatech.com10INSTALLATIONRelocating Wall Switch (Cont.)CAUTION: Be careful of gas lines and wiring whenmoving floor.For Mantel InstallationIf fireplace is to be installed into a mantel, (see ConventionalFireplace Installation, pages 18 and 19) the wall switch may bemounted on either side of the mantel, facing to the side. Do notlocate wall switch anywhere on the front face of the mantel.1. Determine the new location for the wall switch. The wires at-tached to switch are six feet long.2. Remove 2 screws securing plastic wall plate to bracket in fire-place lower cavity. Save screws.3. Remove wire tie holding coiled wire attached to wall switch(see Figure 8).4. Remove wall switch/plate assembly from bracket.5. Carefully pass wall plate and cord through large elongated holein rear of either left or right floor support bracket, depending ondesired location of switch. Pass wall plate and cord through 1.5"diameter hole in side of fireplace outer casing (see Figure 9).6. Pull wall plate and cord from fireplace making sure wall switch/plate assembly will reach desired mounting location withoutstraining cord assembly.If you are mounting wall switch to a wall, continue reading. If youare mounting your wall switch to the side of the mantel, see page 11.INSTALLATIONContinuedFigure 8 - Relocating Switch and Wall PlateCAUTION: Do not apply excessive pull on cord.Figure 9 - Routing Wall Switch/Plate Through Fireplace forRelocationSwitch withWall PlateWire TieBurnerOutletTubeGas Control ValveFireboxBottomWall Switch/Plate AssyHole in OuterCasing Hole inFloorSupportBracketMounting Wall Switch to Wall for Recessed Fireplace7. Create three openings on wall according to Template 1, page39. This is best done by making a pattern to work with on yourwall. Carefully cut page 39/40 from manual and tape papertemplate vertically onto wall at preferred location. Pierce thepaper at the centers of the 2 holes with a nail or sharp pencil,leaving a mark on the wall. Do the same at centers of the fourcircles near the corners of the rectangle.8. Remove paper template from wall.9. Drill 3/8" holes at each mark.10. Using a straight edge and pencil, connect the outer edges ofthe 4 holes for the rectangle (see Figure 10). This will give youcutting lines for the rectangle you will cut in the wall.11. Using a keyhole saw, hack saw blade, drill, file, or other suit-able tool, carefully cut out the rectangular opening.Note: Thecorners of the rectangle may be round.IMPORTANT: Do notexceed the size of the rectangle on template.12. From inside the recessed opening for the fireplace, carefullypass switch/plate assembly through the rectangular opening tothe outside of the wall.13. Using wall anchors supplied in hardware package, fold wallanchor as shown in Figure 11.14. Insert wall anchor, wings first, into hole. Tap anchor flush to wall.15. For thin walls (1/2" or less), insert red key into wall anchor.Push red key to “pop” open anchor wings. See Figure 12.IMPORTANT: Do not hammer key! For thick walls (over 1/2"thick), do not pop open wings.Figure 11 - Folding Anchor Figure 12 - Popping Open AnchorWings for Thin WallsFigure 10 - Using Template for Wall Switch Installation4 3 / 4 "3 3 / 4 "3/8"3/16"3/4"3/8" Diameter2 HolesTemplatefrom ThisManualCuttingLinesMake Marksat Centersof HolesTape