Desa FPVF33NRA Owner's Operation And Installation Manual

Also see for FPVF33NRA: OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL

110148-01BFor more information, visit www.desatech.comFor more information, visit www.desatech.com18OFFPILOTONLOIHAUTOOFFONWARNING: You must operate this fireplace withthe fireplace screen in place. Make sure fireplacescreen is installed before running fireplace.NOTICE: During initial operation of new fireplace,burning logs will give off a paper-burning smell.Open damper or window to vent smell. This will onlylast a few hours.1. STOP! Read the safety information above.2. Make sure equipment shutoff valve is fully open.3. Set selector switch in OFF position.A. This appliance has a pilot which must be lighted by hand.When lighting the pilot, follow these instructions exactly.B. BEFORE LIGHTING smell all around the appliance areafor gas. Be sure to smell next to the floor because some gasis heavier than air and will settle on the floor.WHAT TO DO IF YOU SMELL GAS• Do not try to light any appliance.• Do not touch any electric switch; do not use any phone inyour building.• Immediately call your gas supplier from a neighbor’sphone. Follow the gas supplier’s instructions.• If you cannot reach your gas supplier, call the firedepartment.C. Use only your hand to push in or turn the gas control knob.Never use tools. If the knob will not push in or turn byhand, don’t try to repair it, call a qualified service techni-cian or gas supplier. Force or attempted repair may resultin a fire or explosion.D. Do not use this appliance if any part has been under water.Immediately call a qualified service technician to inspectthe appliance and to replace any part of the control systemand any gas control which has been under water.WARNING: If you do not follow these instructionsexactly, a fire or explosion may result causing prop-erty damage, personal injury or loss of life.FOR YOUR SAFETYREAD BEFORE LIGHTINGOPERATING FIREPLACEWARNING: Burner will come on automaticallywithin one minute when the selector switch is in theON position after the pilot is lit.Figure 38 - Control Knob and Ignitor Button Location (Shown asSupplied, No Control Options)Control KnobIgnitor ButtonSelector SwitchFlame AdjustmentKnob4. Press in and turn control knob clockwise to theOFF position.5. Wait five (5) minutes to clear out any gas. Then smell forgas, including near the floor. If you smell gas, STOP! Fol-low “B” in the safety information, column 1. If you don’tsmell gas, go to the next step.6. Press in and turn control knob counterclockwiseto the PILOT position. Press in control knob for five (5)seconds (see Figure 38).Note: You may be running this heater for the first timeafter hooking up to gas supply. If so, the control knob mayneed to be pressed in for 30 seconds or more. This will al-low air to bleed from the gas system.7. With control knob pressed in, press and release ignitor but-ton. This will light pilot. The pilot is attached to the frontburner. If needed, keep pressing ignitor button until pilot lights.Note: If pilot does not stay lit, contact a qualified serviceperson or gas supplier for repairs. Until repairs are made,light pilot with match. To light pilot with match, see ManualLighting Procedure on page 19.8. Keep control knob pressed in for 30 seconds after lightingpilot. After 30 seconds, release control knob.• If control knob does not pop out when released, contacta qualified service person or gas supplier for repairs.Note: If pilot goes out, repeat steps 4 through 8.9. Slightly push in and turn control knob counterclockwiseto the ON position.10. Wait one minute and switch selector switch to the ON posi-tion to light burner.11. Set flame adjustment knob to any level between HI and LO.CAUTION: Do not try to adjust heating levels byusing the equipment shutoff valve.LIGHTINGINSTRUCTIONSOPERATING FIREPLACEFor Your Safety Read Before LightingLighting Instructions