Desa (V)K36N SERIES Owner's Operation And Installation Manual

111923-01BFor more information, visit www.desatech.comFor more information, visit www.desatech.com24LIGHTINGINSTRUCTIONS1. STOP! Read the safety information above.2. Open lower louver panel.3. Turn off all electric power to the fireplace.4. Push in gas control knob slightly and turn clockwiseto “OFF”.5. Wait five (5) minutes to clear out any gas. Then smell forgas, including near the floor. If you smell gas, STOP! Fol-low “B” in the safety information above. If you don't smellgas, go to the next step.6. The pilot is located by the main burner and should not re-quire accessing for lighting.7. Turn gas control knob counterclockwise to “PILOT”.8. Push in gas control knob all the way and hold. Immedi-ately light the pilot by repeatedly depressing the piezo sparkignitor until a flame appears. Continue to hold for aboutone (1) minute after the pilot is lit. Release gas control knoband it will pop back. Pilot should remain lit. If it goes out,repeat steps 5 through 8.• If gas control knob does not pop up when released, stopand immediately call your service technician or gas supplier.• If the pilot will not stay lit after several tries, turn the gascontrol knob to “OFF” and call your service technicianor gas supplier.9. Turn on all electric power to the fireplace.10. Turn gas control knob counterclockwise to “ON”.11. This valve is equipped with a HI/LO feature. Set fireplaceinput as desired.12. Close lower louver panel.TO TURN OFF GASTO APPLIANCE1. Open lower louver panel.2. Set selector switch in the OFF position to prevent drainingbattery.3. Turn off all electrical power to the appliance if service is tobe performed.4. Push in gas control knob slightly and turn clockwiseto “OFF”.5. Close lower louver panel.Shutting Off Burners Only (pilot stays lit)You may shut off the burners and keep the pilot lit by doing oneof the following:1. Turn gas control knob clockwise to the PILOTposition.2. Set selector switch in the OFF position.MANUAL LIGHTINGPROCEDURE1. Remove glass door (see Removing/Replacing Glass Door,pages 21 and 22).2. Follow steps 1 through 8 under Lighting Instructions.3. Depress gas control knob and light pilot with match.4. Keep gas control knob pressed in for 30 seconds after light-ing pilot. After 30 seconds, release gas control knob. Fol-low steps 10 through 14 under Lighting Instructions.5. Replace glass door (see Removing/Replacing Glass Door,pages 21 and 22).OFFPILOTONLOIHFigure 50 - Control ValvePiezoIgnitorGas ControlKnobVariable Control KnobOPERATING FIREPLACEFor Your Safety Read Before Lighting (Cont.)Lighting InstructionsTo Turn Off Gas To ApplianceManual Lighting ProcedureOptional Hand-Held Remote Operation1. After lighting, let pilot flame burn for about one minute.Turn control knob to ON position. Adjust flame adjust-ment knob anywhere between HI and LO. Slide the selec-tor switch to the REMOTE position (see Figure 51, page25).Note: The burner may light if hand-held remote wason when selector switch was last turned off. You can nowturn the burner on and off with the hand-held remote con-trol unit.Note: All remote control accessories must be purchased sepa-rately (see Accessories, page 36). Follow instructions includedwith the remote control.OPTIONAL HAND-HELDREMOTE OPERATIONNOTICE: You must light the pilot before using the hand-held remote control unit. SeeLighting Instructions.C. Use only your hand to push in or turn the gas controlknob. Never use tools. If the knob will not push in orturn by hand, don't try to repair it, call a qualifiedservice technician. Force or attempted repair mayresult in a fire or explosion.D. Do not use this appliance if any part has been underwater. Immediately call a qualified service techni-cian to inspect the appliance and to replace any partof the control system and any gas control which hasbeen under water.OPERATING FIREPLACEContinued