Desa (V)V42NA(1) Owner's Operation And Installation Manual

Also see for (V)V42NA(1): OWNER'S OPERATION AND INSTALLATION MANUAL

111906-01AFor more information, visit www.desatech.comFor more information, visit www.desatech.com2727OPERATING FIREPLACEContinuedOPTIONAL HAND-HELDREMOTE OPERATIONOPERATING FIREPLACEOptional Hand-Held Remote OperationOFFPIL OTONLOIHONOFFREMOTEONOFFBlower Control Knob(Optional Accessory) VariableControl KnobSelectorSwitch inRemotePositionGas ControlKnob in ONPositionFigure 53 - Setting the Selector Switch, Gas Control Knob, andVariable Control Knob for Remote OperationNOTICE: You must light the pilot before using thehand-held remote control unit. SeeLighting Instruc-tions, page 26.1. After lighting, let pilot flame burn for about one minute.Turn control knob to ON position. Adjust flame adjust-ment knob anywhere between HI and LO. Slide the selec-tor switch to the REMOTE position (see Figure 53).Note:The burner may light if hand-held remote was on whenselector switch was last turned off. You can now turn theburner on and off with the hand-held remote control unit.IMPORTANT: Do not leave the selector switch in the REMOTEor ON position when the pilot is not lit. This will drain the battery.ON/OFF SERIES(MODELS GHRCB AND CGHRCB)Hold the control button on the hand-held remote until burnerturns on. Hold the control button again until burner turns off(see Figure 54).TO LOCK press both buttons on hand-held remote control untillight stops flashing. Hand-held remote control is now locked. Ifthe fire is on it will be turned off automatically. In the lockedstate, the light will not light up when any button is pressed.TO UNLOCK press both buttons together on hand-held remotecontrol until the light stops flashing. The hand-held remote isnow unlocked.THERMOSTAT SERIES(MODELS GHRCTB AND CGHRCTB)The hand-held remote can be operated using either the manualmode (MANU) or thermostatic mode (AUTO) (see Figure 55). Toselect Fahrenheit/Centigrade mode display, carefully press the ˚C/˚F mode button with the end of a paper clip or similar blunt object.Manual Mode1. Press the POWER and LOCK buttons together to turn onthe hand-held remote control.2. Press the MANU button to turn on the fireplace.3. Press the POWER and LOCK buttons together to turn offthe fireplace.Auto (Thermostatic) Mode1. Press the POWER and LOCK buttons together to turn onthe hand-held remote control.2. Press AUTO button to select this mode.3. Set the desired room temperature by pressing the TEMP+ or - buttons.4. Press the POWER and LOCK buttons together to turn offthe fireplaceNote: Do not leave the hand-held remote in the AUTO modeclose to the fireplace. The radiant heat from the fireplace willturn off the fireplace. Ideally, place the hand-held remote in thecenter of the room facing towards the fireplace.Note: Do not hold the hand-held remote for a long time. Bodytemperature will affect its operation in the AUTO mode.Safety FeaturesWhen away from home for an extended period of time or as a childsafety feature to prevent accidental ignition of the fireplace, thereceiver ON/OFF/REMOTE switch should be in the OFF position.Auto Shutoff Feature1. If the average room temperature exceeds 82 degrees Fahr-enheit (28 degrees Centigrade), the hand-held remote con-trol will perform a safety override and shut the fireplaceoff. This feature is not available in the MANU mode.Note: All remote control accessories must be purchased sepa-rately (see Accessories, page 38). Follow instructions includedwith the remote control.Figure 54 - On/Off Hand-Held Remote Control Unit (C)GHRCBControl ButtonTurns BurnersOn and OffFigure 55 - Thermostat Hand-Held Remote Control UnitSelections (C)GHRCTBTurns Hand-HeldRemote On or Offand Allows You toChoose the ManualSettingSelects AutoSettingIncreases RoomTemperature inAUTO ModeLocks System toPrevent AccidentalIgnitionDigital DisplayShowsTemperature andSettingsTurns BurnersOn or OffDecreases RoomTemperature inAUTO Mode