Desa VT32EP Series Owner's Operation And Installation Manual

Also see for T32EN Series: OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL

108860For more information, visit www.desatech.comFor more information, visit www.desatech.com16VENTING INSTALLATIONINSTRUCTIONSContinuedPARTS LISTS FOR VENTING KITS ANDCOMPONENTSDESA International Pipe & Vent KitsNumber DescriptionP47-6 6" Section Coaxial Pipe - GalvanizedP47-12 12" Section Coaxial Pipe - GalvanizedP47-24 24" Section Coaxial Pipe - GalvanizedP47-36 36" Section Coaxial Pipe - GalvanizedP47-48 48" Section Coaxial Pipe - GalvanizedPA47-712 Adjustable 7"-12" Section Coaxial Pipe - GalvanizedVKG-47 Ground Floor Vent Kit - GalvanizedIncludes: 45° Elbow, 7"-12" Adjustable Pipe, Wall Firestop,Horizontal Square Termination, and 16 ScrewsVKB-47 Basement Vent Kit - GalvanizedIncludes: 45° Elbow, 7"-12" Adjustable Pipe, WallFirestop, Horizontal Square Termination, 4' Pipe, 90°Elbow, and 20 ScrewsVKS-47 Snorkel Kit - GalvanizedIncludes: 45° Elbow, 7"-12" Adjustable Pipe, WallFirestop, 36" Snorkel Termination, 4' Pipe, 90° Elbow,and 26 ScrewsVKR-47 Roof Vent Kit - GalvanizedIncludes: 45° Elbow, 7"-12" Adjustable Pipe, Flue Re-strictor, Vertical High Wind Termination, 2' Pipe, 4' Pipe,Firestop Plate, Roof Flashing (0/12-6/12), and 26 ScrewsVKC-47 Corner Vent Kit - GalvanizedIncludes: 45° Elbow, 7"-12" Adjustable Pipe, Hori-zontal Termination, 6" Pipe, 90° Elbow, Wall Firestop,and 18 ScrewsHTK Horizontal Round Termination KitIncludes: Round Termination, Wall Firestop, and 45° ElbowDESA International ElbowsNumber DescriptionE47-45 45° Elbow - GalvanizedE47-90 90° Elbow - GalvanizedDESA International TerminationsNumber DescriptionHT-47 Horizontal Round Termination - GalvanizedHTS-47 Horizontal Square Termination - GalvanizedVT-47 Vertical Round Termination - GalvanizedST-47-14 14" Snorkel Termination - GalvanizedST-47-36 36" Snorkel Termination - GalvanizedDESA International Venting AccessoriesNumber DescriptionSC-47 Storm Collar - GalvanizedWF-47 Wall Firestop - GalvanizedRF-47-6 Roof Flashing - 0 to 6/12 Pitch - GalvanizedRF-47-12 Roof Flashing - 6/12 to 12/12 Pitch - GalvanizedVR-47 Vertical Restrictor - GalvanizedS-47 Combustible Siding Standoff - GalvanizedWS-47 Wall StrapFP-47 Firestop PlateCHECK GAS TYPEUse proper gas type for the fireplace unit you are installing. If youhave conflicting gas types, do not install fireplace. See retailerwhere you purchased the fireplace for proper fireplace according toyour gas type.FIREPLACE INSTALLATIONVENTING INSTALLATION INSTRUCTIONSParts Lists for Venting Kits and ComponentsFIREPLACE INSTALLATIONCheck Gas TypeInstalling Optional Blower AccessoriesModel BK InstallationFollow all instructions provided in the blower accessory kit.1. Attach the power cord to the blower motor by firmly pushing thetwo female terminals at the end of the power cord onto the twospade terminals on the blower motor (see Figure 25, page 17).2. Attach green ground wire from power cord to blower hous-ing using screw provided (see Figure 25, page 17). Tightenscrews securely.3. Place the blower against the lower rear wall of the firebox outerwrapper with the exhaust port directed upward. The blowerwill fit inside the back opening and be held in position againstthe back wall by the magnets (see Figure 25, page 17).INSTALLING OPTIONAL BLOWERACCESSORIESNOTICE: If installing blower in an existing fireplacewith gas connections, shut off gas supply and dis-connect heater from gas supply. Contact a qualifiedservice person to do this.WARNING: If there is a duplex electrical outletinstalled in the right side of the bottom of the fireplacebase area, be sure that the electrical power to the outletis turned off before proceeding with blower installation.Failure to do this may result in serious injury.