Desa VV36ENA1 Series Owner's Operation And Installation Manual

Also see for VICTORIAN V36EN-A Series: OWNER'S OPERATION AND INSTALLATION MANUAL

111253-01AFor more information, visit www.desatech.comFor more information, visit www.desatech.com1601798 Vertical Round High Wind Termination (1)01800 Horizontal Square High Wind Termination (1)01801 14" Snorkel Termination - Galvanized (1)01802 36" Snorkel Termination - Galvanized (1)DESA Venting AccessoriesNumber Description01504 Firestop Plate (4)01505 Adjustable Roof Flashing 0 to 8/12 - Galvanized (6)01506 Steep Pitch Flashing 9/12 to 12/12 - Galvanized (6)01507 Storm Collar - Galvanized (4)01508 Wall Strap (4)01514 Combustible Siding Standoff - Galvanized (1)01607 Wall Firestop - Galvanized (4)VR-58 Vertical Restrictor - GalvanizedVENTING INSTALLATIONINSTRUCTIONSContinuedPARTS LISTS FOR VENTING KITS ANDCOMPONENTS FOR VV361 SERIESDESA (5/8") Pipe & Vent KitsNumber Description01492 Horizontal Square Termination KitIncludes: 45° Elbow (Through 5" Wall), Wall Firestop,Horizontal Square Termination01493 Basic Vertical Termination KitIncludes: Vertical Termination, Adjustable Flashing,Storm Collar01491 Horizontal Round Termination KitIncludes: Round Termination, Wall Firestop, and45° Elbow (Through 5" Wall)01497 12" Section Coaxial Pipe - Galvanized (4)01498 18" Section Coaxial Pipe - Galvanized (4)01499 24" Section Coaxial Pipe - Galvanized (4)01500 36" Section Coaxial Pipe - Galvanized (4)01501 48" Section Coaxial Pipe - Galvanized (4)01513 6" Section Coaxial Pipe - Galvanized (4)01606 Adjustable 17"-24" Section Coaxial Pipe -Galvanized (4)F8030 Adjustable 7"-12" Section Coaxial Pipe - Galvanized (6)D1032 Adjustable 7"-12" Section Coaxial Pipe - Galvanized (1)DESA ElbowsNumber Description01502 45° Elbow - Galvanized (4)01503 90° Elbow - Galvanized (4)DESA TerminationsNumber Description01494 Vertical Round Termination - Galvanized (1)01495 Horizontal Round Termination - Galvanized (1)01496 Horizontal Square Termination - Galvanized (1)FIREPLACE INSTALLATIONVENTING INSTALLATION INSTRUCTIONSParts Lists for Venting Kits and ComponentsFIREPLACE INSTALLATIONCheck Gas TypeInstalling Optional Blower AccessoryModel BK InstallationFollow all instructions provided in the blower accessory kit.1. Attach the power cord to the blower motor by firmly pushing thetwo female terminals at the end of the power cord onto the twospade terminals on the blower motor (see Figure 25, page 17).2. Attach green ground wire from power cord to blower hous-ing using screw provided (see Figure 25, page 17). Tightenscrews securely.3. Place the blower against the lower rear wall of the firebox outerwrapper with the exhaust port directed upward. The blowerwill fit inside the back opening and be held in position againstthe back wall by the magnets (see Figure 25, page 17).INSTALLING OPTIONAL BLOWERACCESSORYNOTICE: If installing blower in an existing fireplacewith gas connections, shut off gas supply and dis-connect heater from gas supply. Contact a qualifiedservice person to do this.WARNING: If there is a duplex electrical outletinstalled in the right side of the bottom of the fireplacebase area, be sure that the electrical power to the outletis turned off before proceeding with blower installation.Failure to do this may result in serious injury.CHECK GAS TYPEUse proper gas type for the fireplace unit you are installing. If yourgas supply is not correct, do not install fireplace. See retailer whereyou purchased the fireplace for proper fireplace according to yourgas type.PARTS LISTS FOR VENTING KITS ANDCOMPONENTS FOR V36 AND VV36 SERIES (CONT.)Number DescriptionRF-58-12 Roof Flashing - 6/12 to 12/12 Pitch, GalvanizedVR-58 Vertical Restrictor, GalvanizedS-58 Vinyl Siding Standoff, GalvanizedWS-58 Wall StrapCS-58 Cathedral Ceiling SupportFP-58 Firestop PlateSF-58 Stucco Flashing - For use with HTS-5