Dynex DX-32E150A11 User Manual

Also see for 32" LED-LCD TV DX-32E150A11: Quick setup guide Guía del usuario Guía De Instalación Rápida Guide de l'utilisateur Guide d'installation rapide

Package contents 3DX-32E150A11• If your TV does not operate normally by following the operatinginstructions. Adjust only those controls that are covered by theoperating instructions because incorrect adjustment of othercontrols may result in damage and will often require extensivework by a qualified technician to restore your TV to its normaloperation.• If your TV has been dropped or damaged in any way.• When your TV exhibits a distinct change in performance.Outdoor antenna groundingIf an outside antenna or cable system is connected to your TV, make surethat the antenna or cable system is grounded to provide someprotection against voltage surges and built-up static charges. Article810 of the National Electrical Code, ANSI/NFPA No. 70, providesinformation with respect to correct grounding of the mast andsupporting structure, grounding of the lead-in wire to an antennadischarge unit, size of grounding conductors, location of theantenna-discharge unit, connection to grounding electrodes, andrequirements for the grounding electrode.Note to CATV system installerArticle 820 of the National Electrical Code, ANSI/NFPA No. 40 providesguidance for correct grounding. Specifically, it states that the cableground must be connected to the grounding system of the building asclose to the point of cable entry as practical.CondensationMoisture will form on the TV if the TV is brought from cool surroundingsinto a warm room or if the temperature of the room rises suddenly.When this happens, the TV's performance may be impaired. To preventthis, let the TV stand in its new surroundings for about an hour beforeswitching it on, or make sure that the room temperature rises gradually.Condensation may also form during the summer if the TV is exposed tothe breeze from an air conditioner. In such cases, change the location ofthe TV.Mobile telephone warningTo avoid interference with your TV picture and sound, operatingproblems, or even damage, keep your cordless and cellular telephonesaway from the TV.End of life directivesYour TV contains tin-lead solder and a fluorescent lamp containing asmall amount of mercury. Disposal of these materials may be regulatedfor environmental reasons. Your TV also contains material that can berecycled and reused. For disposal or recycling information, contact yourlocal authorities or the Electronic Industries Alliance at www.eia.org tofind a recycler in your area.Non-active pixelsThe LCD panel contains almost 3 million thin film transistors, whichprovide exceptionally sharp video quality. Occasionally, a fewnon-active pixels may appear on the screen as a fixed blue, green, or redpoint. These non-active pixels do not adversely affect the performanceof your TV, and are not considered defects.Package contentsMake sure the following items are included in the box with your TV:• Remote control• Composite video and audio cable• AC power cord• AAA batteries (2)• Stand• Stand column• Quick Setup Guide• Screws (8)Installing and removing thestandYou must install your TV into the stand for it to stand upright on acabinet or other flat surface. If you intend to mount your TV on a wall orother vertical surface, you must remove the stand column.Warning: Before attempting assembly or removal of the stand, unplugthe AC power cord.Cautions:Read these instructions thoroughly before attempting this installation.Make sure that you handle your TV very carefully when attemptingassembly or removal of the stand. If you are not sure of your ability todo this, or to use the tools necessary to complete this job, refer to aprofessional installer or service personnel. The manufacturer is notresponsible for any damages or injuries that occur due to mishandlingor improper assembly.When using a table or bench as an aid to assembly, make sure that youplace the TV on a soft cushion or covering to prevent accidentalscratching or damage to your TV’s finish.Installing the standTo install the stand:1 Remove the stand, stand column, and screws from the box.2 Align the holes in the stand with the holes in the stand column,then secure the stand to the stand column with the longer screws(M4) provided.Antenna lead-in wireGrounding clampAntenna discharge unitGrounding conductorsGround clampsPower service grounding electrodesystemElectric service equipment21345671234567